Chrysler 300 2017 Owner'S Manual Download Page 392 | Manualshive

Page: 392 / 488

background image

WARNING!

Do not attempt jump-starting if the battery is frozen. It
could rupture or explode and cause personal injury.

CAUTION!

Do not use a portable battery booster pack or any other
booster source with a system voltage greater than 12
Volts or damage to the battery, starter motor, alternator
or electrical system may occur.

Preparations For Jump-Start

The battery is stored under an access cover in the trunk.
Remote battery posts are located on the right side of the
engine compartment for jump-starting.

WARNING!

•

Take care to avoid the radiator cooling fan whenever
the hood is raised. It can start anytime the ignition
switch is ON. You can be injured by moving fan
blades.

(Continued)

Remote Battery Post Locations

1 — Remote Positive

(+)

Post

2 — Remote Negative

(-)

Post

390

WHAT TO DO IN EMERGENCIES

«
...
390
391
392
393
394
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: Toyota Pages: 529

Brand: Feniex Pages: 6

Brand: Jeep Pages: 603

Brand: Jeep Pages: 80

RadioPRO 5 RP5-GM41

Brand: PAC Pages: 3

Brand: Conrad Pages: 26

2003 Thunderbird

Brand: Ford Pages: 200

Intercooler Kit Type 31

Brand: GReddy Pages: 9

Brand: Meta System Pages: 16

Brand: Reese Explore Pages: 9

THERAPEDIC 2000

Brand: Columbia Pages: 14

Brand: Black+Decker Pages: 21

Brand: Beeper Pages: 20

Brand: Honda Pages: 24

CERTA CTCVINCVR14A

Brand: Kogan Pages: 4

Brand: TATA Motors Pages: 308

2004 JR41 Stratus Sedan

Brand: Dodge Pages: 273

Brand: Mercedes-Benz Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands