Chrysler 300 2017 Owner'S Manual Download Page 181 | Manualshive

Page: 181 / 488

background image

1. Place the ignition in the ON/RUN position.

NOTE:

For vehicles equipped with Keyless Enter-N-Go,

place the ignition in the RUN position with the engine ON.
Make sure while programming HomeLink with the engine
ON that your vehicle is outside of your garage, or that the
garage door remains open at all times.

2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)

away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.

3. Push and hold the HomeLink button you want to

program while you push and hold the hand-held trans-
mitter button.

4. Continue to hold both buttons and observe the indicator

light. The HomeLink indicator will flash slowly and
then rapidly after HomeLink has received the frequency
signal from the hand-held transmitter. Release both
buttons after the indicator light changes from slow to
rapid.

5. At the garage door opener motor (in the garage), locate

the “LEARN” or “TRAINING” button. This can usually
be found where the hanging antenna wire is attached to
the garage door opener/device motor. Firmly push and
release the “LEARN” or “TRAINING” button. On some
garage door openers/devices there may be a light that
blinks when the garage door opener/device is in the
LEARN/TRAIN mode.

NOTE:

You have 30 seconds in which to initiate the next

step after the LEARN button has been pushed.

Training The Garage Door Opener

1 — Door Opener
2 — Training Button

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

179

«
...
179
180
181
182
183
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Porsche 911 Turbo S Wheel

Brand: FANATEC Pages: 9

Brand: RAM Pages: 20

Brand: Uebler Pages: 18

Brand: Edelbrock Pages: 2

Brand: Kolpin Outdoors Pages: 6

Brand: Schartec Pages: 2

Brand: kincrome Pages: 6

Brand: Whipple Pages: 3

Brand: Chevrolet Pages: 412

Brand: Abrams Pages: 12

Brand: Thule Pages: 4

Brand: Peiying Pages: 32

Brand: RAM Pages: 666

PerfectView LCD350

Brand: Waeco Pages: 36

2008 Savana Van

Brand: GMC Pages: 402

Brand: Axxess Pages: 4

Brand: Tesla Pages: 42

Brand: Quadratec Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands