Chrysler 300 2017 Owner'S Manual Download Page 180 | Manualshive

Page: 180 / 488

background image

NOTE:

HomeLink is disabled when the Vehicle Security

Alarm is active.

Before You Begin Programming HomeLink

Be sure that your vehicle is parked outside of the garage
before you begin programming.

For more efficient programming and accurate transmission
of the radio-frequency signal, it is recommended that a new
battery be placed in the hand-held transmitter of the device
that is being programmed to the HomeLink system.

To erase the channels, place the ignition in the ON/RUN
position and push and hold the two outside HomeLink
buttons (I and III) for up 20 seconds or until the red
indicator flashes.

NOTE:

•

Erasing all channels should only be performed when
programming HomeLink for the first time. Do not erase
channels when programming additional buttons.

•

If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.

Programming A Rolling Code

For programming garage door openers that were manufac-
tured after 1995:

These garage door openers can be identified by the
“LEARN” or “TRAIN” button located where the hanging
antenna is attached to the garage door opener. It is NOT the
button that is normally used to open and close the door.
The name and color of the button may vary by manufac-
turer.

Overhead Console HomeLink Buttons

178

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
178
179
180
181
182
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: Yakima Pages: 4

2011 Corolla LE

Brand: Toyota Pages: 19

Brand: AccuAir Pages: 40

Brand: Peak Pages: 10

Brand: Prorack Pages: 14

Brand: Thule Pages: 8

Brand: Chevrolet Pages: 376

Brand: Mazda Pages: 15

Brand: Würth Pages: 36

Brand: P-Invent Pages: 4

Brand: Great Wall Pages: 18

Brand: WIX Pages: 2

Brand: Mercedes-Benz Pages: 398

Brand: Brodit Pages: 2

Telescoping Computer Base C-TCB-34

Brand: Havis-Shields Pages: 1

Brand: PEUGEOT Pages: 107

Brand: Menabo Pages: 8

Brand: Seat Pages: 372

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands