Chrysler 300 2017 Owner'S Manual Download Page 400 | Manualshive

Page: 400 / 488

background image

Rear-Wheel Drive (RWD) Models

The manufacturer recommends towing your vehicle with
all four wheels OFF the ground using a flatbed.

If flatbed equipment is not available, and the transmission
is operable, this vehicle may be flat towed (with all four
wheels on the ground) under the following conditions:

•

The transmission must be in NEUTRAL. Refer to

⬙

Manual Park Release

⬙

in this section for instructions on

shifting the transmission to NEUTRAL when the engine
is off.

•

The towing speed must not exceed 30 mph (48 km/h).

•

The towing distance must not exceed 30 miles (48 km).

If the transmission is not operable, or the vehicle must be
towed faster than 30 mph (48 km/h) or farther than 30
miles (48 km), then the only acceptable method of towing
is with a flatbed truck.

CAUTION!

Towing this vehicle in violation of the above require-
ments can cause severe transmission damage. Damage
from improper towing is not covered under the New
Vehicle Limited Warranty.

Without The Key Fob

Special care must be taken when the vehicle is towed with
the ignition in the LOCK/OFF mode. The only approved
method of towing without the key fob is with a flatbed
truck. Proper towing equipment is necessary to prevent
damage to the vehicle.

398

WHAT TO DO IN EMERGENCIES

«
...
398
399
400
401
402
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: TATA Motors Pages: 94

Brand: GÄN Pages: 24

Brand: Falcon Pages: 8

CommCenter D1 Series

Brand: Federal Signal Corporation Pages: 16

PICASSO XSARA DESIRE 1.6 - MESUREMENT

Brand: CITROEN Pages: 2

Brand: TATA Motors Pages: 92

Brand: Kargo Master Pages: 19

PRIME DESIGN VBR3-FT31B

Brand: Safe Fleet Pages: 12

Brand: Metra Electronics Pages: 5

Brand: Renkforce Pages: 4

Brand: Omix-Ada Pages: 6

Brand: JSPORT Pages: 2

Brand: Needit Pages: 2

KIT ParkingSensor 814

Brand: Gemini Pages: 6

Brand: Dacia Pages: 244

Brand: Kuda-Phonebase Pages: 3

Brand: Opel Pages: 233

Brand: Husky Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands