Chrysler 300 2017 Owner'S Manual Download Page 23

Page: 23 / 488

Programming Additional Key Fobs

Programming key fobs may be performed at an authorized
dealer.

Key Fob Battery Replacement

The recommended replacement battery is one CR2032
battery.

NOTE:

•

Perchlorate Material — special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.

•

Do not touch the battery terminals that are on the back
housing or the printed circuit board.

1. Remove the emergency key by sliding the mechanical

latch on the back of the key fob sideways with your
thumb and then pull the key out with your other hand.

2. Insert the tip of the emergency key or a #2 flat blade

screwdriver into the slot and gently pry the two halves
of the key fob apart. Make sure not to damage the seal
during removal.

Emergency Key Release

1 — Emergency Key Release Button
2 — Emergency Key

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 2017

Reviews:

Related manuals for 300 2017

Brands by name

Popular brands

Chrysler 300 2017, Owner'S Manual

Search results

Summary of Contents for 300 2017

Reviews:

Related manuals for 300 2017

Brands by name

Popular brands