Chrysler 300 2017 Owner'S Manual Download Page 386 | Manualshive

Page: 386 / 488

background image

6. Remove the jack and lug wrench assembly from under

the spare tire. Turn the jack screw to the left to loosen the
lug wrench, and remove the wrench from the jack
assembly.

WARNING!

A loose tire or jack thrown forward in a collision or
hard stop could endanger the occupants of the vehicle.
Always stow the jack parts and the spare tire in the
places provided. Have the deflated (flat) tire repaired
or replaced immediately.

Preparations For Jacking

1. Park the vehicle on a firm, level surface as far from the

edge of the roadway as possible. Avoid icy or slippery
areas.

WARNING!

Do not attempt to change a tire on the side of the
vehicle close to moving traffic, pull far enough off the
road to avoid being hit when operating the jack or
changing the wheel.

2. Turn on the Hazard Warning flasher.

3. Set the parking brake.

4. Place the gear selector into PARK.

5. Turn the ignition to the OFF position.

6. Block both the front and rear of the wheel diagonally

opposite of the jacking position. For ex-
ample, if changing the right front tire, block
the left rear wheel.

Jack Fastener

384

WHAT TO DO IN EMERGENCIES

«
...
384
385
386
387
388
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: Back View Pages: 168

witty park XEV6 Series

Brand: hager Pages: 9

Brand: Front Runner Pages: 5

Wallbox eM4 Single

Brand: ABL Pages: 68

WirelessAIR 73000EZ

Brand: Air Lift Pages: 12

Brand: BrandMotion Pages: 2

Brand: Würth Pages: 36

Brand: Whelen Engineering Company Pages: 9

Brand: Park-Daddy Pages: 22

Brand: Reese Explore Pages: 9

1966 Spider 105

Brand: Alfa Romeo Pages: 46

JEEP GL ADIATOR JT TOPPER ROOF RACK

Brand: JCROffroad Pages: 7

IVH-9000-2R440Q

Brand: Vecow Pages: 110

Brand: ULTIMATE SPEED Pages: 56

Brand: SuperATV Pages: 2

Brand: INNO Pages: 3

MagicWatch MW150

Brand: Waeco Pages: 144

Brand: Brodit Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands