Chrysler 300 2017 Owner'S Manual Download Page 44 | Manualshive

Page: 44 / 488

background image

4. Position the lap belt so that it is snug and lies low across

your hips, below your abdomen. To remove slack in the
lap belt portion, pull up on the shoulder belt. To loosen
the lap belt if it is too tight, tilt the latch plate and pull
on the lap belt. A snug seat belt reduces the risk of
sliding under the seat belt in a collision.

5. Position the shoulder belt across the shoulder and chest

with minimal, if any slack so that it is comfortable and
not resting on your neck. The retractor will withdraw
any slack in the shoulder belt.

6. To release the seat belt, push the red button on the

buckle. The seat belt will automatically retract to its
stowed position. If necessary, slide the latch plate down
the webbing to allow the seat belt to retract fully.

Inserting Latch Plate Into Buckle

Positioning The Lap Belt

42

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
42
43
44
45
46
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

Brand: Blue Ox Pages: 7

Brand: Shad Pages: 3

Brand: Whispbar Pages: 15

Brand: iArmor Pages: 4

Brand: Whispbar Pages: 14

Brand: TATA Motors Pages: 92

ADARAC Aluminum M Series

Brand: aci Pages: 16

Brand: Imiola HAK-POL Pages: 3

Brand: Opel Pages: 32

Brand: rockymounts Pages: 6

Brand: WABCO Pages: 34

FXX ATM Emulator

Brand: BMW Pages: 5

Brand: Mitsubishi Pages: 362

Brand: Reliant Pages: 206

Brand: CITROEN Pages: 394

Truck 2500 2018

Brand: RAM Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands