Chrysler 300 2017 Owner'S Manual Download Page 132 | Manualshive

Page: 132 / 488

background image

WARNING!

Do not adjust the steering column while driving.
Adjusting the steering column while driving or driv-
ing with the steering column unlocked, could cause the
driver to lose control of the vehicle. Failure to follow
this warning may result in serious injury or death.

POWER TILT/TELESCOPING STEERING COLUMN
— IF EQUIPPED

This feature allows you to tilt the steering column upward
or downward. It also allows you to lengthen or shorten the
steering column. The power tilt/telescoping steering col-
umn switch is located below the multifunction lever on the
steering column.

To tilt the steering column, move the switch up or down as
desired. To lengthen or shorten the steering column, pull
the switch toward you or push the switch away from you
as desired.

NOTE:

For vehicles equipped with Driver Memory Seat,

you can use your remote keyless entry key fob or the
memory switch on the driver’s door trim panel to return
the tilt/telescopic steering column to pre-programmed
positions. Refer to “Driver Memory Seat” in this section.

Power Tilt/Telescoping Steering Switch

130

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
130
131
132
133
134
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: Ford Pages: 22

Brand: Safe Fleet Pages: 38

Brand: Kia Pages: 54

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: Nuna Pages: 17

Brand: P-Invent Pages: 4

Brand: Saab Pages: 9

Brand: Yakima Pages: 11

2011 Camry SE V6

Brand: Toyota Pages: 33

Brand: Kleinn Air Horns Pages: 33

Brand: Menabo Pages: 12

Brand: Audiovox Pages: 2

Brand: HawksHead Pages: 10

Brand: Federal Signal Corporation Pages: 12

MagicComfort MSH50

Brand: Waeco Pages: 104

Brand: Edelbrock Pages: 3

2007 JK Wrangler

Brand: Jeep Pages: 456

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands