Chrysler 300 2017 Owner'S Manual Download Page 414 | Manualshive

Page: 414 / 488

background image

Maintenance-Free Battery

Your vehicle is equipped with a maintenance-free battery.
You will never have to add water, nor is periodic mainte-
nance required.

NOTE:

The battery is stored under an access cover in the

trunk. Remote battery terminals are located in the engine
compartment for jump starting. Refer to “Jump-Starting
Procedures” in “What To Do In Emergencies” for further
information.

WARNING!

•

Battery fluid is a corrosive acid solution and can
burn or even blind you. Do not allow battery fluid to
contact your eyes, skin, or clothing. Do not lean over
a battery when attaching clamps. If acid splashes in
eyes or on skin, flush the area immediately with
large amounts of water.

•

Battery gas is flammable and explosive. Keep flame
or sparks away from the battery. Do not use a booster
battery or any other booster source with an output
greater than 12 Volts. Do not allow cable clamps to
touch each other.

•

Battery posts, terminals, and related accessories con-
tain lead and lead compounds. Wash hands after
handling.

•

The battery in this vehicle has a vent hose that
should not be disconnected and should only be
replaced with a battery of the same type (vented).

CAUTION!

•

It is essential when replacing the cables on the
battery that the positive cable is attached to the

(Continued)

Battery Location

412

MAINTAINING YOUR VEHICLE

«
...
412
413
414
415
416
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: kaarta Pages: 29

Brand: Vintage Air Pages: 28

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

Brand: Velleman Pages: 6

Brand: EEZ RV Pages: 31

Brand: Yescom Pages: 4

Brand: Z Automotive Pages: 16

MAGNUM RT Series

Brand: Raptor Series Pages: 6

Tata Indigo Diesel

Brand: TATA Motors Pages: 190

Prime Design HBR-E-FT33B

Brand: Safe Fleet Pages: 12

Brand: Prorack Pages: 20

Brand: VER-MAC Pages: 64

Brand: ACV Pages: 2

Brand: Yakima Pages: 15

Brand: POOL-LINE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands