Chrysler 300 2017 Owner'S Manual Download Page 357 | Manualshive

Page: 357 / 488

background image

NOTE:

When filling warm tires, the tire pressure may need

to be increased up to an additional 4 psi (30 kPa) above the
recommended cold placard pressure in order to turn the
Tire Pressure Monitoring Telltale Light off.

Service TPMS Warning

If a system fault is detected, the TPM Telltale Light will
flash on and off for 75 seconds and then remain on solid.
The system fault will also sound a chime. In addition, the
instrument cluster will display a

⬙

SERVICE TPM SYSTEM

⬙

message for a minimum of five seconds and then display
dashes (- -) in place of the pressure value to indicate which
sensor is not being received.

If the ignition switch is cycled, this sequence will repeat,
providing the system fault still exists. If the system fault no
longer exists, the TPM Telltale Light will no longer flash,
and the

⬙

SERVICE TPM SYSTEM

⬙

message will no longer

display, and a pressure value will display in place of the
dashes. A system fault can occur due to any of the
following:

1. Signal interference due to electronic devices or driving

next to facilities emitting the same radio frequencies as
the TPM sensors.

2. Installing aftermarket window tinting that contains ma-

terials that may block radio wave signals.

3. Accumulation of snow or ice around the wheels or

wheel housings.

4. Using tire chains on the vehicle.

5. Using wheels/tires not equipped with TPM sensors.

Low Tire Pressure Monitor Display

5

STARTING AND OPERATING

355

«
...
355
356
357
358
359
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: Jeep Pages: 6

Brand: Lancia Pages: 386

Brand: AC Schnitzer Pages: 20

Brand: Phonocar Pages: 2

Brand: Honda Pages: 85

2014 Grand Cherokee SRT8

Brand: Jeep Pages: 596

Brand: Skoda Pages: 4

Brand: Whispbar Pages: 17

Brand: Draw tite Pages: 4

ZapCharger Portable C1

Brand: ZAPTEC Pages: 20

2917 Nstallation

Brand: Edelbrock Pages: 1

Brand: Rugged Ridge Pages: 5

Brand: Volvo Pages: 62

Brand: Metra Electronics Pages: 10

Brand: Mazda Pages: 7

Brand: Ford Pages: 2

Brand: Toyota Pages: 596

80-485-142401-RT

Brand: Classic Accessories Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands