Chrysler 300 2017 Owner'S Manual Download Page 118 | Manualshive

Page: 118 / 488

background image

Use the hood prop rod (if equipped) to secure the hood in
the open position.

WARNING!

Be sure the hood is fully latched before driving your
vehicle. If the hood is not fully latched, it could open
when the vehicle is in motion and block your vision.
Failure to follow this warning could result in serious
injury or death.

CAUTION!

To prevent possible damage, do not slam the hood to
close it. Lower hood to approximately 12 inches (30 cm)
and drop the hood to close. Make sure hood is fully
closed for both latches. Never drive vehicle unless
hood is fully closed, with both latches engaged.

LIGHTS

Headlight Switch

The headlight switch is located on the left side of
the instrument panel. This switch controls the op-
eration of the headlights, parking lights, instrument

panel lights, interior lights and fog lights.

Hood Safety Latch

116

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
116
117
118
119
120
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

RadioPRO 5 RP5-GM41

Brand: PAC Pages: 3

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

Brand: Dometic Pages: 158

Brand: Whispbar Pages: 15

BTFREQ PRO BTFMPD3SR

Brand: Scosche Pages: 16

Brand: Caltrend Pages: 2

Brand: Advanced ICE Pages: 4

Brand: Ecco Pages: 9

2011 A3 Sportback

Brand: Audi Pages: 29

Brand: Rugged Ridge Pages: 3

Quantum Wash'n'Wipe N30208

Brand: National Cycle Pages: 12

Brand: Brodit Pages: 2

Brand: PUTCO Pages: 3

Brand: Pet Gear Pages: 4

IGNIS 2022 Series

Brand: Suzuki Pages: 570

Brand: Acura Pages: 347

Brand: SuperATV Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands