OPERATION
Cine-IPM 2K User’s Manual
3-13
020-100164-01 Rev. 1 (01/08)
Enter numbers directly from the keypad in order to specify numbers representing
Cine-IPM 2Ks
, channels (source setups), etc. As each digit is entered, it is displayed
and the cursor moves on. Note that channel numbers are defined with 2 digits—for
example, if you enter only a single digit (such as “7”) for a channel number, the
channel will automatically be defined as “07”. Enter “07” to utilize this channel.
NOTES: 1)
Once you enter the first digit, this digit replaces all old digits.
2)
If you
press any non-numbered key, the number entered up to that point is accepted and
updated as the new value.
3)
Press
Exit
to cancel editing of numerical values.
NOTE:
See
Section 2, Installation and Setup
, for a full explanation of how to
connect sources to the Cine-IPM 2K.
The
Cine-IPM 2K
stores and automatically recalls up to 50 different channels (source
setups) for a variety of inputs. This memory feature allows you to define and
conveniently use a wide variety of customized setups rather than having to repeatedly
re-configure the
Cine-IPM 2K
for different presentations. Depending on what you
have defined, each physical source connection (i.e., input at the
Cine-IPM 2K
) can
have several different channels associated with it.
INPUT –
An input is a source physically connected at the
Cine-IPM 2K
. Pressing
Input 1
,
Input 2
,
Input 3
,
Input 4
,
Input 5
or
Input 6
describes the source signal according to which
input
slot
it is connected.
HOW TO SWITCH TO AN INPUT IN EITHER ONE OF TWO WAYS –
Pressing the
appropriate direct key —
Input 1
,
Input 2
,
Input 3
,
Input 4
,
Input 5
or
Input 6
— is a quick and
seamless way to display from one of the six inputs connected at the front of the
Cine-
IPM 2K
. Alternatively, if the
CP2000’s Touch Panel Controller
(TPC) has been
configured for use with the
Cine-IPM 2K,
you can press the appropriate display
button on the
Main
menu of the TPC. With either method, the image will be
displayed according to the following:
If it is the first time you have used the source/input
(or if you used the input but
did not define a channel by adjusting anything), the
Cine-IPM 2K
will recognize
the new input signal based on its frequencies and polarities, and the projector will
automatically display an image according to default settings for such a signal. By
default, signals will be output from the
Cine-IPM 2K
in 2048 x 1080 format.
If you used the source once before and changed a display parameter
such as
contrast, V-Position, etc., then a channel was automatically created and still exists
in
Cine-IPM 2K
memory (see below). Using an
Input
key will automatically recall
this channel—and all its setup parameters—and update the display accordingly.
If more than one channel exists
for the input, the image will be displayed
according to the setup parameters for the first channel with matching
characteristics.
If PIP is enabled,
an input key
changes the PIP (secondary) image source only. To
switch the main input, use the keypad number keys with “Numbers Select Main
Image” activated.
Editing Numerical Values
X
3.4 Using
Inputs
and Channels
Do I Select an Input
X
Or a Channel?
Summary of Contents for CineIPM-2K
