Canon imageRUNNER ADVANCE C350 series, Service Manual

Page: 960 / 1173

8
8
8-190
8-190
Service Mode > COPIER > TEST > NETWORK
Service Mode > COPIER > TEST > NETWORK
■ NETWORK
COPIER> TEST> NETWORK
PING Network connection check
Lv.1 Details To check connection between this machine and TCP/IP network.
Use case - When checking network connection at the time of installation
- At network connection failure
Adj/set/operate method 1) Turn OFF the main power switch.
2) Connect the network cable to this machine, and then turn ON the
main power switch.
3) Inform the system administrator at user’s site that installation of
this machine is complete, and ask for network setting.
4) Ask the system administrator to check the network connection,
and check the remote host address of PING transmission target.
5) Select the item and enter the remote host address, and then press
OK key and Start key.
OK: Connection is normal. Checking procedure is complete.
NG: Connection failed. Go to step 6) if the cable connection is OK. In
case of cable connection failure, connect again and then go to step 5).
6) Select the item and enter loopback address, and then press OK
key and Start key.
OK: TCP/IP setting of this machine is normal. Go to step 7) to check
NIC.
NG: TCP/IP setting of this machine has failure. Go to step 3) to
check the setting again.
7) Select the item and enter the local host address, and then press
OK key.
OK: Network setting of this machine and NIC are normal. Inform the
system administrator that the trouble is due to network environment
and ask for countermeasure.
NG: Connection failure/fault with NIC. Check connection of NIC/
replace NIC.
Display/adj/set range 0.0.0.0 to 255.255.255.255
At normal state: OK
At failure occurrence: NG
Supplement/memo - Remote host address: IP address of PC terminal in network.
- Loopback address: 127.0.0.1. Checking TCP/IP of this machine is
available because the signal is returned before NIC.
- NIC: Network interface board
- Local host address: IP address of this machine
BML-DISP Set System Monitor scrn: BMlinks support
Lv.2 Details To set whether to only display the device configuration in the System
Monitor screen when supporting BMlinks.
When the setting is switched, the Status and Log are not displayed.
Use case When supporting BMlinks
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: Ordinary System Monitor screen, 1: Screen in which only the
device configuration is displayed
Default value 0
COPIER> TEST> NETWORK
IPV6-ADR Setting of PING send address (IPv6)
Lv.1 Details To set the IPv6 address to send PING.
When PING is sent to this address by COPIER> TEST> NETWORK>
PING-IP6, the network connection condition in the IPv6 environment
can be checked.
Use case When checking the network connection condition in the IPv6
environment
Adj/set/operate method Enter the setting value, and then press OK key.
Caution - Enter a consistent character string as an address of IPv6.
- Enter an address within 39 characters including hexadecimal
numbers (0 to 9, a to f) and a separator (:).
Display/adj/set range Valid IPv6 address
Related service mode COPIER> TEST> NETWORK> PING-IP6
PING-IP6 PING transmission to IPv6 address
Lv.1 Details To send PING to the address specified by IPV6-ADR.
The network connection condition in the IPv6 environment can be
checked.
Use case When checking the network connection condition in the IPv6
environment
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range
0 to 1
0: Not connected, 1: Connected
Related service mode COPIER> TEST> NETWORK> IPV6-ADR
T-8-57