Canon imageRUNNER ADVANCE C350 series, Service Manual

Page: 930 / 1173

8
8
8-160
8-160
Service Mode > COPIER > OPTION > NETWORK
Service Mode > COPIER > OPTION > NETWORK
COPIER> OPTION> NETWORK
PRCLTYPE Setting of dedicated protocol type
Lv.2 Details To set the type of dedicated protocol (CPCA protocol).
When 1 is set, only the commands where security has been
improved are accepted, whereas conventional commands are
rejected.
Use case Upon user’s request (for customization)
- Job assignment from Print/Scan/Fax driver at department
management
- AiRFAX transmission job assignment
- Setting/changing of system administrator function from a remote
utility such as Iwemc
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution With TYPE 1, compatibility with conventional drivers and iW products
may be lost.
Display/adj/set range 0 to 1
0: TYPE 0 (Compatible in conventional manner), 1: TYPE 1
Default value 0
VLAN-SW ON/OFF VLAN participation packets send
Lv.2 Details To set whether to send packets for participating in dynamic VLAN.
Packets are sent at startup, when LAN cable is connected or when
the device recovers from deep sleep.
Use case When participating in dynamic VLAN
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF (Packets are not sent.), 1: ON (Packets are sent.)
Default value 0
Related service mode COPIER> OPTION> NETWORK> VLAN-PKT
Supplement/memo VLAN (Virtual LAN): A method for realizing grouping of terminals
depending on the HUB, switch connection port, MAC address,
protocol, etc.
If IP address of the machine has not been set, an IP address is
assigned after participating in VLAN.
COPIER> OPTION> NETWORK
VLAN-PKT No. of VLAN participation packet to send
Lv.2 Details To set the number of packets for participating in VLAN.
3 sets of packets multiplied by the setting value are sent.
Use case When participating in dynamic VLAN
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution This setting is ignored when the setting is made not to send packets
for participating in VLAN (VLAN-SW=0).
Display/adj/set range 0 to 10
Default value 1
Related service mode COPIER> OPTION> NETWORK> VLAN-SW
Supplement/memo VLAN (Virtual LAN): A method for realizing grouping of terminals
depending on the HUB, switch connection port, MAC address,
protocol, etc.
If IP address of the machine has not been set, an IP address is
assigned after participating in VLAN.
FTPMODE Set of FTP print default operation mode
Lv.1 Details To set the default operation mode of FTP print.
Switch the default operation mode between ASCII mode and BIN
mode in accordance with user’s environment.
Depending on the client application, FTP print becomes available
without executing BIN command.
Use case At installation
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: ASCII mode, 1: BIN mode
Default value 0
SSLMODE Setting of HTTP/HTTPS port open/close
Lv.2 Details To set whether to open or close HTTP/HTTPS port.
When 1 is set, HTTP port is opened whereas HTTPS port is closed.
When 2 is set, HTTP port is closed whereas HTTPS port is opened.
Use case When limiting the port to open because of security concern
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Normal, 1: Open HTTP port (80/8000) only, 2: Open HTTPS port
(443/8443) only
Default value 0