Canon imageRUNNER ADVANCE C350 series, Service Manual

Page: 896 / 1173

8
8
8-126
8-126
Service Mode > COPIER > OPTION > FNC-SW
Service Mode > COPIER > OPTION > FNC-SW
COPIER> OPTION> FNC-SW
FAX-INT Set FAX RX print interruption oprtn mode
Lv.2 Details To set the mode performing interruption operation of FAX reception
print automatically.
Use case Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Normal, 1: Interruption operation mode
Default value 0
PDL-Z-LG Setting of drawing algorithm
Lv.1 Details To switch the draw algorithm of the iR C Series and the iR-ADV C
Series to obtain output the user expects.
When 0 is set, image is output as displayed on the screen by the
new algorithm adopted from the iR-ADV C Series. Pseudo outline
(boundary for processing divided graphics separately) occurred with
the iR C Series does not occur. However, when PDL job with special
data structure is sent, output the user expects may not be obtained.
When 1 is set, the draw algorithm adopted by the conventional iR
C Series is used. Output equivalent to that of the iR C Series can
be obtained; however, draw-related phenomenon occurred with the
series occurs.
Use case Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not use setting value 2 and 3.
Display/adj/set range 0 to 3
0: Drawing algorithm of iR-ADV C series, 1: Drawing algorithm of the
conventional iR C series, 2, 3: For R&D use
Default value 0
COPIER> OPTION> FNC-SW
CDS-LVUP Set to allow CDS periodical update
Lv.1 Details To set whether to allow the user (administrator)/service technician to
perform the periodical update linked with CDS.
When 1 is set, the periodical update setting screen is displayed in
Settings/Registration menu and Register/Update Software menu on
RUI.
When 2 is set, the periodical update can be performed from service
mode.
Use case When allowing the user/service technician to perform periodical
update
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not set 1 in Japan. It is not assumed that the user performs
firmware update.
Display/adj/set range 0 to 2
0: Prohibited, 1: Allowed update by the user, 2: Allowed update by
service technician
Default value JP:0, USA:0, EUR:1, AU:0, CN:0, KR:0, TW:0, ASIA:0
Supplement/memo CDS: Content Delivery System
AMSOFFSW OFF of AMS mode
Lv.1 Details (1) AMS license which is an iR option is installed.
(2) AMS-supported Login application is activated.
Normally, when the conditions (1) and (2) are satisfied, it enters AMS
mode automatically. Use this mode when preferring to disable AMS
mode.
For North/Middle/South America and for Europe, this setting is set to
1 by default. Use this mode when preferring to enable AMS mode.
Use case When preferring to disable AMS mode
When preferring to enable AMS mode (for North/Middle/South
America and for Europe)
Adj/set/operate method 1) Press Counter button, and check that “ACCESS MANAGEMENT
SYSTEM” is displayed on the Device Configuration screen.
2) Set the service mode to 1.
3) Turn OFF/ON the main power switch.
4) Check that AMS is disabled.
Press Counter button, and check that “ACCESS MANAGEMENT
SYSTEM” is not displayed on the Device Configuration screen.
Display/adj/set range 0 to 1
0: AMS mode enabled, 1: AMS mode disabled
Default value JP:0, USA:1, EUR:1, AU:0, CN:0, KR:0, TW:0, ASIA:0
Supplement/memo AMS: Access Management System
When the device is in AMS mode, “ACCESS MANAGEMENT
SYSTEM” is displayed in Check Counter> Check Device
Configuration.