manualshive.com logo in svg

BYD F3, Owner'S Manual

The Nikon F3, a legendary film camera, empowers photography enthusiasts with its exceptional features and versatility. Capture stunning memories with precision using this iconic device. To maximize your photographic experience, download the free Nikon F3 Instruction Manual from manualshive.com for detailed guidance and unleash your creativity.

Share
Download
background image

                                                             F3/F3R  OWNER’S  MANUAL 

 

- 214 - 

b. If the terminal connections are loose, 
tighten their clamp nuts, but do not 
over-tighten it. 
c. Tighten the hold-down clamp only enough 
to keep the battery firmly in place. 
Over-tightening may damage the battery 
case. 

NOTICE 

●

 

Be sure the engine and all 
accessories are off before 
maintaining. 

●

 

When checking the battery, remove 
the ground cable from the negative 
terminal first and reinstall it at last. 

●

 

Be careful not to cause a short 
circuit with tools. 

●

 

Take care that no solution gets into 
the battery when washing it. 

Check battery interior 
Check the battery interior according to the 
instructions and the indicator light of the 
battery. 

NOTICE 

●

 

Charging the battery when the cable 
is connected may seriously damage 
the electric control unit and 
electronic devices. Before 
connecting the battery to a charger, 
disconnect the battery cable first. 

●

 

Operating the power consuming 
devices on your vehicle when the 
engine is stopped may cause the 
battery to be over-discharged. Then, 
the vehicle may fail to start and the 
battery may even be damaged 
permanently.   

 

●

 

Do not operate the power 
consuming devices, like the audio 
system and illuminating system 
when the engine is stopped. 

●

 

Make sure the doors are closed 
and all power consuming devices, 
like lights, are turned off if you are 
leaving your vehicle. 

 

CAUTION 

If the electrolyte is not sufficient, 
please replace the battery. Don’t add 
electrolyte on your own! 

 

C

M

Y

CM

MY

CY

CMY

K

折手文档 1.pdf   1   2011-3-21   17:22:06

Summary of Contents for F3










































































































































































































































Reviews:

No comments

Related manuals for F3

Abarth 595 Owner'S Handbook Manual preview
595
Brand: Abarth Pages: 176
CAMPARK R10 Manual preview
R10
Brand: CAMPARK Pages: 20
HALE MM-03 Driver Manual preview
MM-03
Brand: HALE Pages: 44
Mazda 2012 Mazda6 Owner'S Manual preview
2012 Mazda6
Brand: Mazda Pages: 527
Cadillac 2008 Escalade EXT Owner'S Manual preview
2008 Escalade EXT
Brand: Cadillac Pages: 496
Blue Giant STRONGARM RVR303 Installation & Technical Manual preview
STRONGARM RVR303
Brand: Blue Giant Pages: 48
Toyota RX450h 2010 Emergency Response Manual preview
RX450h 2010
Brand: Toyota Pages: 35
Edelbrock 6883 Instructions preview
6883
Brand: Edelbrock Pages: 2
Inbay 241170-53-1 Installation Manual preview
241170-53-1
Brand: Inbay Pages: 20
SAN HIMA SH-TENT-SY20 User Manual preview
SH-TENT-SY20
Brand: SAN HIMA Pages: 7
Paccar Peterbilt SmartAir Operator'S Manual preview
Peterbilt SmartAir
Brand: Paccar Pages: 58
Mercedes-Benz 300 SL Operator'S Manual preview
300 SL
Brand: Mercedes-Benz Pages: 153
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Brand: H&S Pages: 32
cam 40103 AL Mounting Instructions preview
40103 AL
Brand: cam Pages: 6
E&G Classics Black Ice Mesh Instruction Manual preview
Black Ice Mesh
Brand: E&G Classics Pages: 4
Rugged Ridge 13551.33 Manual preview
13551.33
Brand: Rugged Ridge Pages: 3
Fortin EVO ONE THAR-GM7 Installation Instructions Manual preview
EVO ONE THAR-GM7
Brand: Fortin Pages: 11
Vauxhall Signum Owner'S Manual preview
Signum
Brand: Vauxhall Pages: 310

Brands by name

Popular brands

Load more brands