BYD F3 Owner'S Manual Download Page 185

Page: 185 / 233

F3/F3R OWNER’S MANUAL

- 181 -

be recorded. This record will be helpful when
your vehicle needs repair or maintenance
service.

Does your vehicle need repairing?

Be on the alert for changes in
performance, sounds, and visual tip-offs
that indicate service is
needed. Some important clues are
as follows:

●

Engine missing, stumbling, or pinging

●

Obviously decreasing of power

●

Strange engine noises

●

A leak under the vehicle (however,
water dripping from the air conditioning
after use is normal.)

●

Change in exhaust sound (this may

indicate a dangerous carbon monoxide
leak. Drive with the windows opened
and have the exhaust system checked
immediately.)

●

Flat-looking tire; excessive tire squeal
when cornering; uneven

tire wear

●

Vehicle pulls to one side when driving
straight on a level road

●

Strange noises related to suspension
movement

●

Loss of brake effectiveness; spongy
feeling upon brake or clutch petal; pedal
almost touches floor; vehicle pulls to
one side when braking

●

Engine coolant temperature stays
continually higher than normal

If you notice any of these clues, take your
vehicle to your BYD service station as soon
as possible. It probably needs adjustment or
repair

CAUTION

Do not continue driving with the

vehicle unchecked. It could result in

serious vehicle damage and possibly

personal injury.

BYD F3/F3R

maintenance schedule

BYD F3/F3R maintenance schedule helps
guarantee steady, safe, and economic
driving and reduce malfunctions.

The service interval for scheduled
maintenance bases on the odometer reading
or time interval. The one that comes first
prevails.

Summary of Contents for F3










































































































































































































































Search results

Summary of Contents for F3

Reviews:

Related manuals for F3

Brands by name

Popular brands

BYD F3, Owner'S Manual

Search results

Summary of Contents for F3

Reviews:

Related manuals for F3

Brands by name

Popular brands