BYD F3 Owner'S Manual Download Page 2 | Manualshive

Page: 2 / 233

background image

F3/F3R OWNER’S MANUAL

Foreword

Thanks for choosing BYD F3/F3R. To help you operate and maintain BYD F3/F3R, please read this

Owner's Manual

thoroughly.

BYD F3 uses electric injection engine, and the wiring harness is very complex, so please do not install the following additional electric equipment by
yourself: burglar alarm, central control lock, power window, audio devices and so on. Any damages or malfunctions caused by the above
modifications are not covered by warranty.
Throughout this manual, you will see safety and vehicle damage warnings. You must follow these warnings carefully to avoid possible injury or
damage.
The types of warning, what they look like, and how they are used in this manual are explained as follows:

Important Information

NOTICE

Be convenient to overhaul, please abide the following.

All pictures in this manual are schematic and only for references.
BYD reserves the right to modify the technical features and
specifications in this manual without notice.
Thanks for choosing BYD F3/F3R. All suggestions are welcome.

CAUTION

This is a warning against anything which may cause injury to people or
damages to your vehicle.

When you see the safety symbol shown above, it means:
“Do not …”; “Do not do this”; or “Do not let this happen”.

«
1
2
3
4
...
»

Summary of Contents for F3










































































































































































































































Reviews:

No comments

Related manuals for F3

WirelessAIR 73000EZ

Brand: Air Lift Pages: 12

Brand: V8 equipment Pages: 17

2007 MazdaSpeed6

Brand: Mazda Pages: 12

Brand: JANE Pages: 58

Truck Diesel Supplement 2012

Brand: RAM Pages: 174

Brand: Fab Fours Pages: 13

Brand: Draw tite Pages: 4

Brand: EFILive Pages: 25

Brand: Brink Pages: 26

Brand: Ford Pages: 40

Brand: Edelbrock Pages: 2

Brand: Mercedes-Benz Pages: 93

Telescoping Computer Base C-TCB-34

Brand: Havis-Shields Pages: 1

Brand: PEUGEOT Pages: 107

Brand: Ranger design Pages: 22

Tipper Remote Kit

Brand: Nugent Pages: 21

Brand: EUFAB Pages: 18

Brand: Racepak Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands