BYD F3 Owner'S Manual Download Page 163

Page: 163 / 233

F3/F3R OWNER’S MANUAL

- 159 -

4. Have everyone get out of the vehicle on

the side away from

traffic.

5. Read the following instructions

thoroughly.

CAUTION

Upon jacking, be sure to observe the
following to reduce the possibility of
personal injury:

●

Follow jacking instructions.

●

Do not put any part of your body
under the vehicle supported by the
jack. Otherwise, personal injury may
occur.

●

Do not start or run the engine while
your vehicle is supported by the jack.

●

Stop the vehicle on a level firm
ground, firmly set the parking brake,
and put the

transmission in neutral. Block the
wheel diagonally opposite to the
one being changed if necessary.

●

Make sure to set the jack properly
in the jack point. Raising the
vehicle with a jack improperly
positioned will damage the vehicle
or may allow the vehicle to fall off
the jack and cause personal injury.

●

Never get under the vehicle when
the vehicle is supported by the jack
alone.

●

Use the jack only for lifting your
vehicle during wheel changing.

●

Do not raise the vehicle with
someone in the vehicle.

●

When raising the vehicle, do not
place any objects on top of or
underneath the jack.

●

Raise the vehicle only high
enough to remove and change the
tire.

NOTICE

Do not continue driving with a deflated
tire. Driving even a short distance can
damage a tire and wheel beyond
repair.

Summary of Contents for F3










































































































































































































































Search results

Summary of Contents for F3

Reviews:

Related manuals for F3

Brands by name

Popular brands

BYD F3, Owner'S Manual

Search results

Summary of Contents for F3

Reviews:

Related manuals for F3

Brands by name

Popular brands