manualshive.com logo in svg

BYD F3, Owner'S Manual

The Nikon F3, a legendary film camera, empowers photography enthusiasts with its exceptional features and versatility. Capture stunning memories with precision using this iconic device. To maximize your photographic experience, download the free Nikon F3 Instruction Manual from manualshive.com for detailed guidance and unleash your creativity.

Share
Download
background image

                                                         F3/F3R  OWNER’S  MANUAL 

 

- 47 - 

 

Remove excess length of the belt and 
adjust the belt position. 

To shorten the belt, pull the free end of the 
belt. 
Position the loin belt as low as possible on 
your hips, not on your loin. Then, adjust it to a 
snug fit. 
 

 

CAUTION 

Both high-positioned and loose-fitting 
lap belts could cause serious injuries 
due to sliding under the lap belt during a 
collision or other unintended result. 
Keep the lap belt positioned as low on 
hips as possible. 

 
 
 
 
 
 
 
 
 

 

CAUTION 

●

 

After inserting the tab, make sure the 
tab and buckle are locked and that 
the belt is not twisted. 

●

 

Do not insert coins, clips, etc. in the 
buckle as this may prevent you from 
properly latching the tab and buckle. 

●

 

If the seat belt does not function 
normally, immediately contact BYD 
AUTO service station. Do not use the 
seat until the seat belt is fixed. It can 
not protect an adult occupant or 
your child from injury. 

Summary of Contents for F3










































































































































































































































Reviews:

No comments

Related manuals for F3

Feniex AM600 Instruction Manual preview
AM600
Brand: Feniex Pages: 6
Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Brand: Jeep Pages: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Brand: Jeep Pages: 6
Kargo Master 80070 Assembly Lnstructions preview
80070
Brand: Kargo Master Pages: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Brand: Kargo Master Pages: 21
Kargo Master 40201 Installation Manual preview
40201
Brand: Kargo Master Pages: 4
Quadratec QR3 Installation Manual preview
QR3
Brand: Quadratec Pages: 8
Yakima KingJoe 2 Quick Start Manual preview
KingJoe 2
Brand: Yakima Pages: 7
Yakima BowDown Quick Start Manual preview
BowDown
Brand: Yakima Pages: 6
Yakima LOCKN'LOAD Manual preview
LOCKN'LOAD
Brand: Yakima Pages: 10
Yakima HitchSki Quick Start Manual preview
HitchSki
Brand: Yakima Pages: 12
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Brand: Subaru Pages: 34
BGS technic 40108 Manual preview
40108
Brand: BGS technic Pages: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Brand: Oldsmobile Pages: 344
ABL eMH3 Installation Manual preview
eMH3
Brand: ABL Pages: 66
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
Ford 2001 Explorer Owner'S Manual preview
2001 Explorer
Brand: Ford Pages: 256
Oypla Leisure 4269 User Manual preview
4269
Brand: Oypla Leisure Pages: 4

Brands by name

Popular brands

Load more brands