manualshive.com logo in svg

BYD F3, Owner'S Manual

The Nikon F3, a legendary film camera, empowers photography enthusiasts with its exceptional features and versatility. Capture stunning memories with precision using this iconic device. To maximize your photographic experience, download the free Nikon F3 Instruction Manual from manualshive.com for detailed guidance and unleash your creativity.

Share
Download
background image

                                                         F3/F3R  OWNER’S  MANUAL 

 

- 156 - 

 

Below shows the connecting point: 

 

The joint of jump starting engine 

Do not connect the cable to or near any part 
that moves when the engine is cranked. 

CAUTION 

For connections, to avoid serious 
injury, do not lean over the battery or 
accidentally let the jumper cables or 
clamps touch anything except the 
correct battery terminals or the ground.

 
5. 

Run the engine in the vehicle with the 
booster battery at about 2000 rpm with 
the accelerator pedal lightly pressed. 

6. 

Carefully disconnect the cables in the 
exact reverse order: the   

negative cable and then the positive 
cable. 

7. 

Carefully dispose of the cloths covering 

the battery: they may now contain 
sulfuric acid. 

8. 

If removal is needed, put all plugs of 
battery back to its initial position. 

If the reason of your battery discharging is not 
apparent (for example, lights left on), you 
should have it checked at your BYD AUTO 
service station.

Summary of Contents for F3










































































































































































































































Reviews:

No comments

Related manuals for F3

Garmin BC 30 Owner'S Manual preview
BC 30
Brand: Garmin Pages: 2
Safe Fleet PRIME DESIGN VRI3-E-PM11 Manual preview
PRIME DESIGN VRI3-E-PM11
Brand: Safe Fleet Pages: 12
Tamiya KO PROPO RTF 2002 ESC Manual preview
KO PROPO RTF 2002 ESC
Brand: Tamiya Pages: 2
Romik 2137 2D Installation Instructions Manual preview
2137 2D
Brand: Romik Pages: 6
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Brand: B-Speech Pages: 24
AutoWatch 457 Rli Wiring Diagram preview
457 Rli
Brand: AutoWatch Pages: 4
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Brand: KRAFTWERK Pages: 2
Saab 12 787 887 Installation Instructions Manual preview
12 787 887
Brand: Saab Pages: 12
Bilstein E4-WM5-Y479A00 Mounting Instruction preview
E4-WM5-Y479A00
Brand: Bilstein Pages: 7
Fabbri BICI OK 2 Manual preview
BICI OK 2
Brand: Fabbri Pages: 32
Whelen Engineering Company SAK34 Installation Manual preview
SAK34
Brand: Whelen Engineering Company Pages: 2
Roadmaster Even Brake 9400 Owner'S Manual preview
Even Brake 9400
Brand: Roadmaster Pages: 20
AUTOTECH 10.109.418K Installation Instructions preview
10.109.418K
Brand: AUTOTECH Pages: 4
Volkswagen Zubehör 000 071 105 D Installation Instructions Manual preview
000 071 105 D
Brand: Volkswagen Zubehör Pages: 133
EUFAB 16476 Operating Instructions Manual preview
16476
Brand: EUFAB Pages: 18
Vmac A700308 Installation Manual preview
A700308
Brand: Vmac Pages: 16
Rally Armor IMF63 Installation Instruction preview
IMF63
Brand: Rally Armor Pages: 4
Gator ARV50T User Manual preview
ARV50T
Brand: Gator Pages: 18

Brands by name

Popular brands

Load more brands