manualshive.com logo in svg

BYD F3, Owner'S Manual

The Nikon F3, a legendary film camera, empowers photography enthusiasts with its exceptional features and versatility. Capture stunning memories with precision using this iconic device. To maximize your photographic experience, download the free Nikon F3 Instruction Manual from manualshive.com for detailed guidance and unleash your creativity.

Share
Download
background image

                                                         F3/F3R  OWNER’S  MANUAL 

 

- 198 - 

Positioning the jack 

 

Front 

 

Rear 

When jacking up your vehicle with the jack, 
position the jack correctly as shown in the 
illustrations. 

CAUTION 

When jacking, be sure to observe the 
following to reduce the possibility of 
personal injury: 

●

 

Avoid inhale the exhaust gas of 

engine. The exhaust gas contains

 

colorless and odorless monoxide that 

can cause deaths. 

●

 

Do not put any part of your body 

under the vehicle supported by the 

jack. Personal injury may occur. 

●

 

Do not start or run the engine while 

your vehicle is supported by the jack.

●

 

Stop the vehicle on a level firm 

ground, firmly set the parking brake, 

and put the transmission in neutral. 

Block the wheels on the opposite side 

or the jack up point if necessary. 

 

●

 

Make sure to put the jack in a 
proper position. Personal injury or 
vehicle damage may occur if it is 
jacked up incorrectly. 

●

 

Don’t go under the vehicle if it’s 
upheld only by the jack. The 
vehicle needs to be 
underpropped. 

●

 

Do not raise the vehicle with 
someone in the vehicle. 

When raising the vehicle, do not place 
any  objects  on  top  of  or  underneath 
the jack. 
 

 

 

NOTICE 

Make sure to place the jack correctly, or 
your vehicle may be damaged. 

 
 

Summary of Contents for F3










































































































































































































































Reviews:

No comments

Related manuals for F3

Jeda Wireless Pad Manual preview
Wireless Pad
Brand: Jeda Pages: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Brand: Jeep Pages: 496
U & Me Brothers LK-168A Manual preview
LK-168A
Brand: U & Me Brothers Pages: 6
minnid 1.240.344 Operating Instructions Manual preview
1.240.344
Brand: minnid Pages: 44
MASCOT SMARTCHARGER User Manual preview
SMARTCHARGER
Brand: MASCOT Pages: 12
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Brand: Safe Fleet Pages: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Brand: Honda Pages: 4
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Brand: Havis-Shields Pages: 1
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Brand: Mercedes-Benz Pages: 91
Navman T1 F20 User Manual preview
T1 F20
Brand: Navman Pages: 10
Macrom EF-AR1-5561 Manual preview
EF-AR1-5561
Brand: Macrom Pages: 10
KLAUS Multiparking trendvario6X00 Service Manual preview
trendvario6X00
Brand: KLAUS Multiparking Pages: 72
Cadillac 2000 DeVille Service Manual Addendum preview
2000 DeVille
Brand: Cadillac Pages: 19
r.LiNK RL2-MMI3G-Q3 Manual preview
RL2-MMI3G-Q3
Brand: r.LiNK Pages: 21
Toyota Tundra guide Manual preview
Tundra guide
Brand: Toyota Pages: 672
Pet Gear TL9000 Instruction Manual preview
TL9000
Brand: Pet Gear Pages: 4
Suzuki IGNIS 2022 Series Manual preview
IGNIS 2022 Series
Brand: Suzuki Pages: 570
Poison Spyder TrailGate TJ Installation Instructions preview
TrailGate TJ
Brand: Poison Spyder Pages: 5

Brands by name

Popular brands

Load more brands