manualshive.com logo in svg

BYD F3, Owner'S Manual

The Nikon F3, a legendary film camera, empowers photography enthusiasts with its exceptional features and versatility. Capture stunning memories with precision using this iconic device. To maximize your photographic experience, download the free Nikon F3 Instruction Manual from manualshive.com for detailed guidance and unleash your creativity.

Share
Download
background image

                                                         F3/F3R  OWNER’S  MANUAL 

 

- 161 - 

Blocking the wheel 

 

Block the wheel diagonally opposite to the 
flat tire to keep the vehicle from rolling 
when it is jacked up. 

When blocking the wheel, place a wheel 
block in front of one of the front wheels or 
behind one of the rear wheels. 

Loosening wheel nuts

 

 

Loosen all the wheel nuts. 
Always loosen the wheel nuts before raising 
the vehicle. 
Turn the wheel nuts anticlockwise to loosen. 
To get maximum leverage, fit the wrench to 
the nut so that the handle is on the right side, 
as shown above. Grab the wrench near the 
end of the handle and pull up the handle.   

Be careful that the wrench does not slip off 
the nut. 
Do not remove the nuts yet: just unscrew 
them about one-half turn. 

CAUTION 

Do not use oil or lubricant on bolts 
and nuts. Otherwise, nuts will get 
loosed and the tire will break off from 
vehicle, thus causing a severe 
accident.   

 
 
 
 

 
 
 

Summary of Contents for F3










































































































































































































































Reviews:

No comments

Related manuals for F3

Federal Signal Corporation CommCenter D1 Series Installation And Service Instructions Manual preview
CommCenter D1 Series
Brand: Federal Signal Corporation Pages: 16
FABBRI PORTATUTTO 17405400 Assembly Instructions preview
17405400
Brand: FABBRI PORTATUTTO Pages: 2
Roav R5141 Owner'S Manual preview
R5141
Brand: Roav Pages: 10
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Brand: SuperATV Pages: 3
Ford Windstar 2003 Quick Reference Manual preview
Windstar 2003
Brand: Ford Pages: 2
Fiat 500 L 2019 User Manual preview
500 L 2019
Brand: Fiat Pages: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Brand: Honda Pages: 6
Chrysler Stratus LHD 1997 Interactive Electronic Service Manual preview
Stratus LHD 1997
Brand: Chrysler Pages: 1534
Mercedes-Benz R 350 2012 Operator'S Manual preview
R 350 2012
Brand: Mercedes-Benz Pages: 368
Metra Electronics 99-5819 Installation Instructions Manual preview
99-5819
Brand: Metra Electronics Pages: 8
Subaru Legacy 2011 Quick Reference Manual preview
Legacy 2011
Brand: Subaru Pages: 19
National Cycle Quantum Wash'n'Wipe N30208 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30208
Brand: National Cycle Pages: 12
Mobileye C2-270 User Manual preview
C2-270
Brand: Mobileye Pages: 29
Butts of Bawtry TBT4700 Quick Start Manual preview
TBT4700
Brand: Butts of Bawtry Pages: 2
Belkin LineCast Auto FM User Manual preview
LineCast Auto FM
Brand: Belkin Pages: 15
Rover 75 Saloon Owner'S Handbook Manual preview
75 Saloon
Brand: Rover Pages: 285
Xpresskit 20110601 Installation Manual preview
20110601
Brand: Xpresskit Pages: 12
Kuda 293950 Installation Instruction preview
293950
Brand: Kuda Pages: 3

Brands by name

Popular brands

Load more brands