manualshive.com logo in svg

BYD F3, Owner'S Manual

The Nikon F3, a legendary film camera, empowers photography enthusiasts with its exceptional features and versatility. Capture stunning memories with precision using this iconic device. To maximize your photographic experience, download the free Nikon F3 Instruction Manual from manualshive.com for detailed guidance and unleash your creativity.

Share
Download
background image

                                                         F3/F3R  OWNER’S  MANUAL 

 

- 163 - 

Changing wheels

 

 

Remove the wheel nuts and change the 
tire. 

Lift the flat tire straight off and put it aside. 
Roll the spare wheel into position and align 
the holes in the wheel with the bolts. Then lift 
up the wheel and get at least the top bolt 
started through its hole. Wiggle the tire and 
press it back over the other bolts. 
 

 

Before putting on wheels, remove any 
corrosion on the mounting surfaces with a 
wire brush or such. Installation of wheels 
without good metal-to-metal contact at the 
mounting surface can cause wheel nuts to 
loosen and eventually cause a wheel to come 
off while driving. 

Re-installing all wheel nuts

 

 

Reinstall the wheel nuts with the tapered end 
inward and tighten them as much as you can 
by hand. Push on tire back and see if you can 
tighten them more. 
 
 
 

 

Summary of Contents for F3










































































































































































































































Reviews:

No comments

Related manuals for F3

Toyota 4Runner 2019 Quick Reference Manual preview
4Runner 2019
Brand: Toyota Pages: 52
Firestone Ride-Rite Air Helper Springs 2173 Installation Instructions preview
Ride-Rite Air Helper Springs 2173
Brand: Firestone Pages: 4
RHOX LGT-381L Installation Instructions Manual preview
LGT-381L
Brand: RHOX Pages: 8
cam 40103 AL Mounting Instructions preview
40103 AL
Brand: cam Pages: 6
rockymounts SplitRailLS Installation Instructions Manual preview
SplitRailLS
Brand: rockymounts Pages: 6
Pontiac 2006 Relay Getting To Know Manual preview
2006 Relay
Brand: Pontiac Pages: 20
Acura TSX 2014 Advanced Technology Manual preview
TSX 2014
Brand: Acura Pages: 19
Ford 2009 Edge Owner'S Manual preview
2009 Edge
Brand: Ford Pages: 325
Westin 32-1660 Instructions preview
32-1660
Brand: Westin Pages: 3
Pogo Alert+ Operating Instructions Manual preview
Alert+
Brand: Pogo Pages: 40
Chevrolet 1995 C/K Pickup Owner'S Manual preview
1995 C/K Pickup
Brand: Chevrolet Pages: 483
HOLDEN Malibu EM 2015 Owner'S Handbook Manual preview
Malibu EM 2015
Brand: HOLDEN Pages: 330
Kargo Master 408TC Installation Manual preview
408TC
Brand: Kargo Master Pages: 14
Audiovox Rear Observation System Package RVMPKG2 Installation Manual preview
Rear Observation System Package RVMPKG2
Brand: Audiovox Pages: 15
Kuda-Phonebase 041300 Installation Instruction preview
041300
Brand: Kuda-Phonebase Pages: 3
Erde ST1272A Assembly Instructions preview
ST1272A
Brand: Erde Pages: 3
Canyon CNE-CCA02 Quick Manual preview
CNE-CCA02
Brand: Canyon Pages: 2
Honda 2013 Fit EV Emergency Response Manual preview
2013 Fit EV
Brand: Honda Pages: 24

Brands by name

Popular brands

Load more brands