manualshive.com logo in svg

BYD F3, Owner'S Manual

The Nikon F3, a legendary film camera, empowers photography enthusiasts with its exceptional features and versatility. Capture stunning memories with precision using this iconic device. To maximize your photographic experience, download the free Nikon F3 Instruction Manual from manualshive.com for detailed guidance and unleash your creativity.

Share
Download
background image

                                                         F3/F3R  OWNER’S  MANUAL 

 

- 177 - 

agents, make sure their ingredients do 
not include the substances mentioned 
above. 

●

 

If you use a liquid car freshener, do 

not spill the liquid onto the vehicle’s 
interior surfaces. It may   

contain the ingredients mentioned 
above. Immediately clean any spill 
using the method mentioned above.

 
Interior leather upholstery

 

The leather upholstery may be cleaned with 
neutral detergent for wool. 
Remove dirt using a piece of soft cloth 
dampened with 5% solution of neutral 
detergent for wool. Then, thoroughly wipe off 

all traces of detergent with a piece of clean 
damp cloth. 
After cleaning or whenever any part of the 
leather gets wet, dry with a piece of soft clean 
cloth. Allow the   
leather to dry in a ventilated shaded area. 
 
 

 

CAUTION 

●

 

If a stain should fail to come out with 

a neutral detergent, apply a cleaner 
that does not contain an organic 
solvent. 

●

 

Never use organic substances such 

as benzene, alcohol, gasoline, 
alkaline or acid solutions to clean the 

leather as these could cause 
discoloring. 

●

 

Use of a nylon brush or synthetic 

fiber cloth, etc. may scratch the fine 
grained surface of the leather. 

●

 

Mildew may develop on soiled   

leather upholstery. Be 

Summary of Contents for F3










































































































































































































































Reviews:

No comments

Related manuals for F3

AA Products KX405 Instruction Manual preview
KX405
Brand: AA Products Pages: 8
RAM Commercial PROMASTER 2020 Quick Reference Manual preview
PROMASTER 2020
Brand: RAM Commercial Pages: 12
GMC 2005 Sierra Denali Owner'S Manual preview
2005 Sierra Denali
Brand: GMC Pages: 428
Mercedes-Benz GLA 250 2019 Operator'S Manual preview
GLA 250 2019
Brand: Mercedes-Benz Pages: 346
Thule Kit 1514 Instructions preview
Kit 1514
Brand: Thule Pages: 4
Vintage Air 561163 Manual preview
561163
Brand: Vintage Air Pages: 28
Kia Sportage 2018 Features & Functions Manual preview
Sportage 2018
Brand: Kia Pages: 54
Ford 2004 Navigator Owner'S Manual preview
2004 Navigator
Brand: Ford Pages: 368
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Brand: Havis-Shields Pages: 1
Edelbrock 29135 Installation Instructions preview
29135
Brand: Edelbrock Pages: 2
Mercedes-Benz 1989 560 SL Owner'S Manual preview
1989 560 SL
Brand: Mercedes-Benz Pages: 93
Scosche HUD580GC Manual preview
HUD580GC
Brand: Scosche Pages: 12
Calix M5T 204 Assembly Instructions preview
M5T 204
Brand: Calix Pages: 4
Metra Electronics 95-7322 Installation Instructions Manual preview
95-7322
Brand: Metra Electronics Pages: 16
Mercedes-Benz GLC 2020 Operator'S Manual preview
GLC 2020
Brand: Mercedes-Benz Pages: 66
Or-Fab 82301 Installation Instructions preview
82301
Brand: Or-Fab Pages: 3
Chevrolet CORVETTE 2020 Owner'S Manual preview
CORVETTE 2020
Brand: Chevrolet Pages: 324
Buick 1998 Century Owner'S Manual preview
1998 Century
Brand: Buick Pages: 372

Brands by name

Popular brands

Load more brands