BYD F3 Owner'S Manual Download Page 112

Page: 112 / 233

Heating

For best results, set controls to:

Fan speed:

any value except “0”

Temperature:

towards WARM (red zone)

Air intake:

FRESH (outside air)

Air flow:

FLOOR

Air conditioning:

OFF

F3/F3R OWNER’S MANUAL

- 108 -

For quick heating, select re-circulated air

for a few minutes. To keep the windows
from fogging, select FRESH after the
interior of the vehicle has been warmed.

Press the “A/C” button on for dehumidified

heating.

Choose floor/windshield air flow to heat the

vehicle interior while

defrosting or defogging the windshield.

Air condition

For best results, set controls to:

Fan speed:

any value except for “0”

Temperature:

towards COLD (blue zone)

Air intake:

FRESH (outside air)

Air flow:

PANEL

Air conditioning:

For quick cooling, turn the air cycle mode
selector to re-circulated air for a few minutes.

Ventilation

For best results, set controls to:

Fan speed:

any value except for “0”

Temperature:

towards COLD (blue zone)

Air intake:

FRESH (outside air)

Air flow:

PANEL

Air conditioning:

OFF

Defogging

The inside of the windshield

For best results, set controls to:

Fan speed:

any value except for “0”

Temperature:

towards WARM (red zone)

Air intake:

FRESH (outside air)

Air flow:

WINDSHIELD

Air conditioning:

On humid days, do not blow cold air on the

windshield, as the difference between the
outside and inside temperatures could
make the fogging worse.

CMY

折手文档 1.pdf 1 2011-3-21 17:39:54

Summary of Contents for F3










































































































































































































































Search results

Summary of Contents for F3

Reviews:

Related manuals for F3

Brands by name

Popular brands

BYD F3, Owner'S Manual

Search results

Summary of Contents for F3

Reviews:

Related manuals for F3

Brands by name

Popular brands