Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 24

Page: 24 / 140

2-2

Section 2

Boat Operation

Ignition Shutoff Switch

Your boat is equipped with one ignition shutoff switch.

The ignition shutoff switch is located on the control

console face.

The ignition shutoff switch is designed to shut off the

outboard engine if you move away from the helm sta-

tion by accident, either by falling down or by being

ejected from the helm seat. Both of these situations

can be caused by unsafe operating techniques or

severe operating conditions. Do not use the ignition

shutoff switch to stop the outboard engine during nor-

mal boat operation.

You should connect the ignition shutoff switch clip and

lanyard to a sturdy part of your clothing. If you move

beyond the scope of the lanyard, the ignition shutoff

switch will be activated and the outboard engine will

shut off immediately.

WARNING

Do not activate the ignition shutoff switch

during normal operations when the boat is on

plane. Activating the ignition shutoff switch at

planing speeds will cause the boat to suddenly

decelerate, possibly injuring or ejecting

passengers.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands