Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 53

Page: 53 / 140

2-31

Boat Operation

Section 2

Slings

You can use a spreader bar and slings to lift your boat.

The system must be professionally certified to a work-

ing load of at least 6,000 pounds (2722 kg) with a

safety factor of five. The slings must be a wide, flat,

belted design to distribute the load and protect the

boat.

Position the spreader bar and slings to lift the boat

evenly. The boat’s longitudinal center of gravity (LCG)

is approximately 84 inches (213 cm) forward of the

transom. Position the slings so they do not contact

any thru-hull fittings on the sides or bottom of the boat.

Attach at least two guide lines to control the boat while

it is being moved.

Move the boat slowly.

DANGER

Never allow anyone to be in the boat or under

the boat while you are lifting it. A mistake in the

lifting procedure or a component failure could

cause serious injury or death.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Brands by name

Popular brands