Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 70

Page: 70 / 140

3-16

Section 3

Fuel Systems

Contaminated Gasoline

Water from condensation and sediment from contami-

nated gasoline can collect in your fuel tank. Contami-

nated gasoline can damage boat fuel system

components, corrode the fuel tank, clog the fuel filter,

and damage your engine’s fuel system.

Your fuel filter inspection and servicing routine is

directly related to the quality and quantity of gasoline

that you take on-board. You should check the fuel fil-

ter sight bowl for evidence of moisture before and after

every mission.

Refer to

Blended Fuels

in this section for more infor-

mation about water in gasoline.

If your fuel shows evidence of moisture or particulate

contamination, consult a professional tank-cleaning

contractor about having your fuel tank pumped out

and cleaned.

Verify that the contractor is fully licensed and that he

can dispose of the contaminated gasoline following all

state and federal regulations.

WARNING

Do not allow any liquid gasoline to enter the

boat or accumulate in the bilge. Liquid gasoline

is a fire and explosion hazard. Gasoline vapor

is extremely flammable and highly explosive

under certain conditions.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Brands by name

Popular brands