Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 32

Page: 32 / 140

2-10

Section 2

Boat Operation

You must determine the correct engine trim adjust-

ments through experimentation or experience, based

on your mission loads and operating conditions.

• Your single-lever control has an engine trim

switch located on the control lever.

• The trim switch moves the outboard engine

through its trim range to change general boat

operating angle.

• Adjusting engine trim angle can affect ride com-

fort and boat performance. 4° “bow up” is an

average setting for boat operating angle.

• Adjusting engine trim angle can improve fuel

economy, improve ride comfort, and compensate

for uneven boat loading.

CAUTION

Do not trailer your boat with the engine in its

fully tilted position.

CAUTION

Center the engine before tilting to avoid contact

with any special towing equipment on your

boat.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Brands by name

Popular brands