background image

4-20

Section 4

Boat Systems

4-20

Section 4

Boat Systems

4-20

Section 4

Boat Systems

4-20

Section 4

Boat Systems

4-20

Section 4

Boat Systems

Siren & Strobe Light

Your boat might be equipped with a Whelen

® 

flush-

mount siren and strobe light.  The normal mounting

location is on the forward side of the console.

Use the siren control head to operate the various

strobe, radio, siren, and public address features.

The siren amplifier circuit is protected by a 10-amp

blade fuse located in the accessory fuse block inside

the control console.

Turn off the siren and strobe features when they are

not required to avoid discharging the house battery.

Turning the house battery OFF-ON switch to the 

OFF

position at the end of your mission will cut power to the

siren amplifier and strobe power circuits.

Refer to the Whelen operator’s manual for detailed

information about the siren and strobe functions.

Floodlights

Your boat might be equipped with one or more 12

VDC floodlights.  The floodlights are usually mounted

on the T-top frame.  You can use the floodlights to illu-

minate the deck or surrounding water while you are

working or doing boarding operations.

Each floodlight is controlled by an OFF-ON rocker

switch located on the T-top radio box switch panel.

Each floodlight power circuit is protected by a 10-amp

blade fuse in the T-top fuse block.

Turn off the floodlights when they are not required to

avoid discharging the house battery.

Turning the house battery OFF-ON switch to the 

OFF

position at the end of your mission will cut power to all

of the floodlight circuits.

Summary of Contents for 20 Justice Series













































































































































Reviews: