Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 57

Page: 57 / 140

3-3

Fuel Systems

Section 3

The fuel tank fill cap is located on the port gunwale,

midship. The fill cap is labeled

GAS

. The fuel fill cap

and fill hose are equipped with a flow-control valve

that will not allow liquid gasoline to escape from the fill

cap during normal fueling operations.

The fuel tank is included in the boat’s bonding system.

All exposed metallic components that are served by

the 12 VDC electrical system, but do not carry current,

are electrically connected to an internal bonding sys-

tem. Design benefits of the bonding system include:

• Provide a low resistance electrical connection

among isolated metal components, which might

be subject to electrolytic corrosion caused by

stray voltage

• Prevent the build-up of electrical potential on

exposed metal parts, which might cause personal

injury

• Provide a low resistance electrical connection to

ground when components are exposed to voltage

spikes such as a lightning strike

• Reduce radio frequency interference (RFI)

The common bonding conductor, a green #8 awg insu-

lated copper wire, connects the fuel fill assembly and

the fuel tank to a grounding plate located on the hull.

WARNING

Do not allow any liquid gasoline to enter the

boat or accumulate in the bilge. Liquid gasoline

is a fire and explosion hazard. Gasoline vapor

is extremely flammable and highly explosive

under certain conditions.

CAUTION

Read and understand all fuel-related

information and warnings in your outboard

engine operator’s manual.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Brands by name

Popular brands