manualshive.com logo in svg

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Share
Download
Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 86

4-14

Section 4

Boat Systems

4-14

Section 4

Boat Systems

4-14

Section 4

Boat Systems

4-14

Section 4

Boat Systems

4-14

Section 4

Boat Systems

Trim Tab Control Box

The trim tab control box, located inside the control

console, operates on power supplied through the

accessory fuse block.  The trim tab power circuit is

protected a 20-amp blade fuse.  The trim tab control

box senses 12 VDC when the outboard engine ignition

key switch is in the ON position. 

Because the trim tab control box senses switched

12 VDC at the outboard engine ignition switch:

• The trim tab system will only operate when the

outboard engine ignition switch is 

ON

• The trim tabs will automatically retract when the

outboard engine ignition switch is turned 

OFF

!

CAUTION

The trim tabs will automatically retract when the
outboard engine is turned OFF.  Make sure that
both trim tabs are fully retracted before you put
the boat on a trailer, cradle, or boatlift.  Contact
with the trim tabs can cause serious damage to
the tabs and the boat.

Summary of Contents for 20 Justice Series













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands