Boston Whaler 20 Justice Series Operation & Maintenance Manual Download

Page: 115 / 140

5-19

Electrical Systems

Section 5

Accessory Fuse Block

The accessory fuse block is a ten-position, blade-fuse

design. It is located inside the control console. A typi-

cal fuse block could include the following branch cir-

cuits:

• 12 VDC outlet

• Whelen power supply

• Trim tab control box

• Console lights

• Courtesy lights

• Several spares

The accessory fuse block is convenient when install-

ing or servicing accessory components that are

located in or on the control console.

See

Wire Color Chart

in this section for wire colors.

T-top Fuse Block

The T-top electronics fuse block is a ten-position,

blade-fuse design. It is located inside the T-top radio

box.

The T-top electronics fuse block is convenient when

installing or servicing radios and electronics mounted

in or on the T-top.

See

Wire Color Chart

in this section for wire colors.

Electronics Distribution Panel

The electronics distribution panel (optional) has eight

switchable circuit breakers controlled by one main 50-

amp switchable breaker. It is located inside the con-

trol console.

The electronics distribution panel is convenient when

installing or servicing sensitive navigation equipment

such as chart plotters and radar units.

See

Wire Color Chart

in this section for wire colors.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands