Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 40

Page: 40 / 140

2-18

Section 2

Boat Operation

Maneuvering

Maneuvering this boat requires experience and a high

level of skill. Always operate any boat within the limits

of your experience. If you do not have this experience,

ask someone to instruct you or gain experience

through experimentation under controlled conditions.

If you do not have this experience, do not operate this

boat under high-risk conditions, such as:

• Heavy wind or current

• High-traffic areas

• Mission-related time limitations

• Confined or restricted areas

• Carrying hazardous cargo

• Compromised boat or engine systems

Always follow established boating regulations and

directions from boating law authorities when maneu-

vering or underway. Always maneuver around

objects, docks, and other boats at

idle speed

Always evaluate the wind strength, wind direction, cur-

rent strength, and current direction as you maneuver.

If possible, approach a dock or another boat moving

into the wind or current.

Always keep your crew informed and prepared. Have

mooring lines and fenders in place before you reach

the dock.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands