Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 107

Page: 107 / 140

5-11

Electrical Systems

Section 5

DC Power Distribution

All DC electrical devices and systems in your boat are

controlled and protected by

six

main 12 VDC power

distribution circuits.

Outboard Engine

Main 12 VDC power circuit 1 of 6

provides power for

starting the outboard engine through a battery OFF-

ON switch connected to a Group 24 1000 MCA bat-

tery. The outboard engine battery OFF-ON switch is

located in the control console, just inside the console

door.

The main power and negative cables from the out-

board engine route through the splash-well boot and

connect to this power circuit through a main two-posi-

tion, heavy-duty terminal strip located near the tran-

som. The main terminal strip simplifies engine

removal for service or replacement.

Turning the outboard engine battery OFF-ON switch to

the

OFF

position at the end of your mission will cut

power to the outboard engine and its accessories.

See

Wire Color Chart

in this section for wire colors.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands