Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 127

Page: 127 / 140

6-11

Boat Maintenance

Section 6

Fuel System

Your boat is equipped with one below-deck aluminum

fuel tank that requires little maintenance. You should

visually inspect the fuel tank and all associated hoses

and fittings for leaks or deterioration before each mis-

sion. If you suspect a leak, you should have your boat

serviced immediately by an experienced marine tech-

nician.

Your boat might be equipped with one Racor

320R-

RAC-01 gasoline fuel filter. This filter features a

water-separating 10-micron filter element, a replace-

able spin-on canister, and a clear bowl to help detect

water in your fuel.

Your inspection and servicing routine is directly related

to the quality and quantity of gasoline that you take on-

board. You should check the sight bowl for evidence

of moisture before and after every mission.

Replace the filter element on this schedule, whichever

happens first:

• Every 100 operating hours

• Annually

• Noticeable engine performance loss

WARNING

Do not allow any liquid gasoline to enter the

boat or accumulate in the bilge. Liquid gasoline

is a fire and explosion hazard. Gasoline vapor

is extremely flammable and highly explosive

under certain conditions.

WARNING

Follow the manufacturer’s recommendations

exactly when servicing this gasoline filter to

avoid engine damage or fuel leaks. Refer to the

manufacturer’s instruction booklet in your

owner’s bag for detailed information about

these service procedures.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands