Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 128

Page: 128 / 140

6-12

Section 6

Boat Maintenance

Steering System

Your boat is equipped with a manual hydraulic steer-

ing system.

Be sure to check the operation of the steering system

before each mission. Turn the steering wheel from

hard port to hard starboard while watching for any

unusual engine movement and listening for any

unusual noise. If any unusual movement or noise is

detected, have the steering system serviced before

operating the boat.

Weekly, check the steering fluid level in the helm res-

ervoir. It should be maintained at no less than ½ inch

and no more than

⅛

inch below the bottom of the filler

cap threads.

Be careful not to overfill the reservoir.

WARNING

Follow the steering system manufacturer’s

maintenance recommendations exactly.

Improper maintenance might cause loss of

steering, which could cause property damage

or serious injury.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Brands by name

Popular brands