Boston Whaler 20 Justice Series Operation & Maintenance Manual Download Page 69

Page: 69 / 140

3-15

Fuel Systems

Section 3

Vent Hose Replacement

Removal

Your fuel tank is vented at the engine splashwell.

Loosen the two hose clamps and remove the hose

from the elbow at the fuel tank. Remove the clamps

from the hose.

Loosen the two hose clamps and remove the hose

from the vent fitting. Remove the clamps from the

hose. Pull the hose from under the deck plate slowly

until it is completely free.

Installation

If your fuel system is equipped with a carbon canister,

transfer the canister to the new vent hose. Match the

original orientation of the canister exactly during instal-

lation. Route the vent hose under the deck until it

reaches the elbow on the fuel tank. Secure the hose

to the tank elbow with two hose clamps.

Attach the other end of the hose to the vent fitting at

the engine splashwell and secure with two hose

clamps.

WARNING

Do not allow any liquid gasoline to enter the

boat or accumulate in the bilge. Liquid gasoline

is a fire and explosion hazard. Gasoline vapor

is extremely flammable and highly explosive

under certain conditions.

Summary of Contents for 20 Justice Series












































































































































Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands

Boston Whaler 20 Justice Series, Operation & Maintenance Manual

Search results

Summary of Contents for 20 Justice Series

Reviews:

Related manuals for 20 Justice Series

Brands by name

Popular brands