Belanger insta-KLEEN Owner'S Manual Download Page 13 | Manualshive

Page: 13 / 88

background image

insta-KLEEN

™ MANUAL

1MANUL334

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

7

Introduction

IMPORTANT Safety Information

–

MUST READ

It is imperative to your safety and the safety of others to always follow
safe work procedures.

WARNING

–

WEAR APROPRIATE PERSONAL PROTECTION GEAR WHEN NEAR

POWERED UP EQUIPMENT WITH ENCLOSURE DOOR/COVER OPEN.

WARNING

–

IT IS THE RESPONSIBILITY OF THE SITE OWNER TO PROPERLY

INSTRUCT THE WASH USER ON THE PROPER USE OF THE WASH AND TO
INSTRUCT THEM THAT THE WASH BEGINS AUTOMATICALLY AFTER
PROPERLY LOADING THE VEHICLE.

WARNING

–

ALL MACHINE COMPONENTS HANDLED

DURING  INSTALLATION,  MAINTENANCE  AND/OR  SERVICE
MUST BE HANDLED WITH A DEVICE APPROPRIATELY RATED
AND  IN  SUITABLE  CONDITION  TO  LIFT  AND/OR  HANDLE
THE  WEIGHT  OF  THE  COMPONENT.  WHEN  COMPONENTS
ARE  HANDLED  BY  HAND,  USE  PROPER  LIFTING
TECHNIQUES TO AVOID INJURY.

WARNING

–

DO NOT ATTEMPT TO SERVICE AREAS OF THIS EQUIPMENT

ABOVE  1.8  M  (6  FT)  WITHOUT  WEARING AN  APPROVED  SAFETY  HARNESS.
DO NOT ATTEMPT TO ACCESS UPPER AREAS OF THIS EQUIPMENT EXCEPT BY
USING  AN  APPROVED  SAFETY  LADDER  IN  GOOD  OPERATING  CONDITION.
DO  NOT  USE  TABLES,  CHAIRS,  OR  OTHER  NON-APPROVED  CLIMBING
EQUIPMENT OTHER THAN AS STATED HEREIN.

WARNING

–

HEARING PROTECTION IS REQUIRED FOR PERSONS SUCH AS

WASH ATTENDENT OR SERVICE TECHNICIAN IF PRESENT IN THE WASH BAY
OR THE AREA OF THE DRYER WHILE THE DRYER IS OPERATING. EQUIPMENT
OPERATES ABOVE 80 dB.

WARNING - DO NOT OPERATE THIS EQUIPMENT WITHOUT ALL GUARDS
AND COVERS IN PLACE.

CAUTION

–

ALWAYS WEAR SAFETY GLASSES WHEN PERFORMING

MAINTENANCE ON ANY EQUIPMENT.

WARNING - SITE OWNER RESPONSIBLE FOR CREATING WASH USE
INSTRUCTIONS VISIBLE TO USER IN NATIVE LANGUAGE.

«
...
11
12
13
14
15
...
»

Summary of Contents for insta-KLEEN

























































































Reviews:

No comments

Related manuals for insta-KLEEN

Profile PDW8680N

Brand: GE Pages: 48

Monogram ZBD5600

Brand: GE Pages: 24

Triton XL GSD6900 Series

Brand: GE Pages: 2

Brand: GE Pages: 16

Brand: GE Pages: 2

Brand: GE Pages: 20

Brand: Gorenje Pages: 38

Brand: EdgeStar Pages: 13

Brand: Kärcher Pages: 24

Brand: Parmco Pages: 22

Brand: unicraft Pages: 18

Brand: Danby Pages: 56

Brand: Smeg Pages: 35

Brand: Dual Pumps Pages: 20

VOLTAS Beko DF15A

Brand: TATA Motors Pages: 53

Brand: Haier Pages: 10

THERMOCOOL TLSA13B

Brand: Haier Pages: 18

Brand: Haier Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands