Belanger insta-KLEEN Owner'S Manual Download Page 18

Page: 18 / 88

insta-

KLEEN™ MANUAL

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL334

Introduction

Description of insta-KLEEN

™ System

From the base insta-KLEEN

™, the following options can be selected (continued):

14)

Reverse Osmosis (RO)

: Spot Free systems are available in several sizes and are great for final rinse

applications.

15)

Wei

gand™ Wash Card Systems

: These units can be added to the insta-KLEEN

™ system for tracking

vehicle washes and authorization.

16)

™ Standard Guide Rail:

Guide rail system that captures the front driver-side tire of a vehicle, and

assists in proper vehicle alignment, guiding the vehicle throughout the length of the car wash.

17)

™ Right-hand Drive Guide Rail:

Guide rail system that will capture the front driver-side tire of a

vehicle in the International market, and assists in proper vehicle alignment, guiding the vehicle
throughout the length of the car wash.

18)

™ Vehicle Width Guide Rail:

Guide rail system that will capture and contain the entire vehicle, and

assists in proper vehicle alignment, guiding the vehicle throughout the length of the car wash.

19)

Chameleon

Arch:

The C

hameleon® Arch is made of quality aluminum and stainless-steel construction,

bold colors, vibrant lighting, and flexible branding options. Offered in spray applicator and utility cross-
over arch configurations.

Important:

Please refer to the system drawings in this manual for space requirements and typical

layouts. Refer to the supplied electrical prints for electrical requirements. Install all tunnel equipment
per its corresponding component manual and your site-drawings.

This document will cover topics that are specific to
the insta-KLEEN

™ Wash System. For information

on how to install wash components, refer to their
manuals, supplied electrical prints and site-
specific drawings.

Summary of Contents for insta-KLEEN

























































































Search results

Summary of Contents for insta-KLEEN

Reviews:

Related manuals for insta-KLEEN

Brands by name

Popular brands

Belanger insta-KLEEN, Owner'S Manual

Search results

Summary of Contents for insta-KLEEN

Reviews:

Related manuals for insta-KLEEN

Brands by name

Popular brands