Belanger insta-KLEEN Owner'S Manual Download Page 46

Page: 46 / 88

insta-

KLEEN™ MANUAL

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL334

Installation

Utilities

3/4”

(19.05mm) Hose to Rinse Arch

3/4”

(19.05mm) Hose to Zone 2 Water/Chemical

3/4”

(19.05mm) Hose to Optional Presoak

3/4”

(19.05mm) Hose to Zone 1 Water/Chemical

1”

(25.4mm) Hose to Fresh

or Reclaim Water

1”

(25.4mm) Hose

Fresh or RO Water

•

System comes standard with three
valve assemblies

•

Optional valve available for
Presoak

•

Injection Tee included on valve if
Drying Agent option is purchased

Optional Drying Agent

Optional Presoak

Zone 1 and 2 Soap

•

System comes standard with
one chemical pump

•

Optional pumps available for
Drying Agent and Presoak

Injection Tee

NOTE:

If one Rinse Arch for RO

and

the Presoak option was purchased, remove

the Rinse Arch Valve from the ICC (shown above) and plumb it in-line with

the RO Unit and the Rinse Arch. Plumb a longer 1/2

”

(13.45mm) poly-flow

line from the Wax Pump to the Injector at the Tee on the Solenoid Valve.

Summary of Contents for insta-KLEEN

























































































Search results

Summary of Contents for insta-KLEEN

Reviews:

Related manuals for insta-KLEEN

Brands by name

Popular brands

Belanger insta-KLEEN, Owner'S Manual

Search results

Summary of Contents for insta-KLEEN

Reviews:

Related manuals for insta-KLEEN

Brands by name

Popular brands