Belanger insta-KLEEN Owner'S Manual Download Page 50

Page: 50 / 88

insta-

KLEEN™ MANUAL

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL334

Operation

insta-

KLEEN™ Control Center (ICC)

Operator Interface

Data Register

•

D140

→

Front Roller count

•

D141

→

Rear Roller count

•

D142

→

Conveyor off delay

•

D143

→

Titan run time

•

D144

→

Titan delay on

•

D145

→

Pre-soak run time

•

D146

→

Pre-soak delay on

•

D147

→

Zone 1 water off delay

•

D148

→

Zone 2 water on delay

•

D149

→

Dryer off delay

•

D150

→

Extra-function off delay

•

D151

→

NOT USED

•

D152

→

NOT USED

•

D153

→

NOT USED

•

D154

→

Program Version

•

D155

→

Displays number of washed vehicles

M Setting Screen

This screen used to change/display the setting of M500 to M509

To navigate among M500 to M509 press the OK key to get underline cursor flashing. Once
cursor is flashing use + and

– keys to navigate from M500 to M509.

To change setting navigate to M bit that you wish to change then press OK key to toggle
ON/OFF. _ represents off and represents on.

Summary of Contents for insta-KLEEN

























































































Search results

Summary of Contents for insta-KLEEN

Reviews:

Related manuals for insta-KLEEN

Brands by name

Popular brands

Belanger insta-KLEEN, Owner'S Manual

Search results

Summary of Contents for insta-KLEEN

Reviews:

Related manuals for insta-KLEEN

Brands by name

Popular brands