Belanger insta-KLEEN Owner'S Manual Download Page 27

Page: 27 / 88

insta-KLEEN

™ MANUAL

1MANUL334

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Installation

The stanchions are to be installed on the exit section of the
Guide Rail at the 4 locations shown in the side image.

1) Remove the button-head screw and nut shown below. Discard the nut.

Loosen the lag bolt shown in image #2 to allow you to slightly lift the
Guide Rail off the floor. Locate the supplied support stanchion.

2) Slide the stanchion into place as in image #3 and replace the button-

head screw into the tapped hole in the stanchion (image #4). Secure
the stanchion to the floor with 1/2” (12.7mm) lags (image #5).

Image #1

Image #2

Image #3

Image #4

Image #5

Summary of Contents for insta-KLEEN

























































































Search results

Summary of Contents for insta-KLEEN

Reviews:

Related manuals for insta-KLEEN

Brands by name

Popular brands

Belanger insta-KLEEN, Owner'S Manual

Search results

Summary of Contents for insta-KLEEN

Reviews:

Related manuals for insta-KLEEN

Brands by name

Popular brands