M‑3425A Instruction Book
2–8
To access the
STATUS
menu and begin monitoring,
proceed as follows:
1.
Press the
ENTER
pushbutton.
2.
If Level Access is active, the following is
displayed:
ENTER ACCESS CODE
0
a. Input the required Access Code, then
press
ENTER
.
b. If the proper Access Code has been
entered, the HMI will return:
LEVEL #(1,2 or 3)
Access Granted!
VOLTAGE RELAY
VOLT curr freq v/hz
V
c. Go to Step 4.
3.
If Level Access is not Active, then the
following will be displayed:
VOLTAGE RELAY
VOLT curr freq v/hz
4.
Press the Right arrow pushbutton until
the following is displayed:
STATUS
config sys STAT
5.
Press the
ENTER
pushbutton
,
the
following will be displayed:
VOLTAGE STATUS
VOLT curr freq v/hz
V
6.
Press the Right or Left arrow pushbutton
until the desired parameter is selected
(upper case), then press
ENTER
. The
HMI will display the selected parameter.
7.
Press the
ENTER
pushbutton to move
down within the
STATUS
menu to the
desired category. To exit a specific
category and continue to the next menu
category, press the
EXIT
pushbutton.
Status Monitoring (From Relay Front Panel)
The menu categories for monitored values are:
•
Voltage Status
: phase voltages, neutral
voltage, positive sequence voltage,
negative sequence voltage, zero sequence
voltage, third harmonic neutral voltage,
field ground measurement circuit, stator
low frequency injection voltage
• Current Status:
phase currents (A–B–C/a-
b-c), differential current, neutral current,
ground differential current, positive
sequence current, negative sequence
current, zero sequence current, stator low
frequency injection current
• Frequency Status
: frequency, rate of
change of frequency
• Volts/Hz Status:
volts per hertz
• Power Status
: real power, reactive power,
apparent power, power factor
• Impedance Status
: impedance (Zab, Zbc,
Zca), positive sequence impedance, field
ground resistance
•
Sync Check Status
: 25S Sync Check and
25D Dead Volt
•
BRKR Monitor
•
81A Accum. Status
• IN/OUT Status
: Status of input and output
contacts
• Timer
:
51V Delay Timer, 51N Delay Timer,
46IT Delay Timer, 24IT Delay Timer
•
Relay Temperature
• Counters
: output, alarm counter
• Time of Last Power up
• Error Codes
• Checksums:
setpoints, calibration, ROM
Summary of Contents for M-3425A
