6–77
Testing – 6
4.
To start or stop the clock press
ENTER
,
the following is displayed:
a. If the clock is already running the
following will be displayed:
CLOCK TEST
CLOCK STOP
CLOCK TEST
01-Jan-2003 01:01:80
b. If the clock was NOT running the
following will be displayed:
CLOCK TEST
CLOCK START
CLOCK TEST
01-Jan-2003 01:01:01
NOTE
: To preserve battery life the clock should be
OFF if the unit is to be left de-energized
for a long period of time.
5.
The clock can be toggled ON or OFF by
pressing any arrow pushbutton or
ENTER
.
To exit the Clock ON/OFF mode press
EXIT
, the following will be displayed:
CLOCK TEST
-DONE-
6.
To exit the CLOCK ON/OFF Diagnostic
Menu press
EXIT
.
7.
If all Diagnostic Testing is complete, then
exit the diagnostic menu by pressing
EXIT
,
PRESS EXIT TO EXIT DIAGNOSTIC
MODE
is displayed, then press
EXIT
a
second time.
Relay OK LED Flash/Illuminated
This feature provides the user with the ability to set
the relay OK LED to either Flash or be Illuminated
when the relay is working properly.
1.
If the relay is already in the Diagnostic
Mode, then go to Step 2.
If the relay is NOT in the Diagnostic Mode,
then enter the relay diagnostic mode by
performing the steps described in the
Entering Relay Diagnostic Mode section
of this chapter, then go to Step 2.
2.
Ensure that the Diagnostic Menu is
selected to FLASH RELAY OK LED
(Upper Case).
FLASH RELAY OK LED
output input led target
button disp
com1 com2 com3 clock
LED
cal factory
If LED (to the left of cal) is not selected
(Upper Case), then use the Right/Left
arrow pushbuttons to select LED.
3. Press
ENTER
, the following will be
displayed:
FLASH RELAY OK LED
OFF on
4.
Select (upper case) either ON (to flash) or
OFF (to Illuminate) by pressing the right/
left arrow pushbutton once.
5. Press
ENTER
, the following will be
displayed:
FLASH RELAY OK LED
-DONE-
6.
To exit the FLASH RELAY OK LED
Diagnostic Menu press
EXIT
.
7.
If all Diagnostic Testing is complete, then
exit the diagnostic menu by pressing
EXIT
,
PRESS EXIT TO EXIT DIAGNOSTIC
MODE
is displayed, then press
EXIT
a
second time.
Auto Calibration
Refer to the following Section 6.4, Auto Calibration,
for more information on that function.
AUTO CALIBRATION
clock led CAL factory
Factory Use Only
This function is provided to allow access by factory
personnel.
FACTORY USE ONLY
clock led cal FACTORY
Summary of Contents for M-3425A
