4–12
M‑3425A Instruction Book
SYSTEM CLOCK
This feature allows the user to set the relay internal
clock. The clock is used to time stamp system events
and oscillograph operations.
The clock is disabled when shipped from the
factory (indicated by “80” seconds appearing on
the clock) to preserve battery life. If the relay is to
be unpowered for an extended length of time, the
clock should be stopped (from Diagnostic Mode
or IPScom Figure 4-7). If the IRIG-B interface is
used, the hours, minutes, and seconds information
in the clock will be synchronized with IRIG-B time
information every hour.
The relay can accept a modulated IRIG-B
signal using the rear panel BNC connector, or a
demodulated TTL level signal using extra pins on
the rear panel COM2 RS-232 interface connector
(see Figure B-4 for COM2 pinout.) If the TTL signal
is to be used, then Jumper 5 will be required to be
positioned (see Section 5.5, Circuit Board Switches
and Jumpers).
IPScom Set Date/Time
To set the relay Date/Time perform the following:
NOTE
: Communication must be established with
the target relay for this procedure.
1.
From the IPScom Main Screen menu
select
Relay/Setup/Setup Date & Time
.
IPScom will display the Setup Date/Time
dialog screen (Figure 4-7).
Figure 4-7
Setup Date/Time Dialog Screen
2.
Enter the desired Date and/or Time.
3. Select
SAVE
, IPScom will return to the
Main Screen.
HMI SET DATE and TIME
1.
Press the
ENTER
pushbutton.
2.
If Level Access is active, the following is
displayed:
ENTER ACCESS CODE
0
a.
Input the required Access Code, then
press
ENTER
.
b. If the proper Access Code has been
entered, the HMI will return:
LEVEL #(1,2 or 3)
Access Granted!
VOLTAGE RELAY
VOLT curr freq v/hz
c.
Go to step 4.
3.
If Level Access is not active, then the
following is displayed:
VOLTAGE RELAY
VOLT curr freq v/hz
4.
Press the
RIGHT arrow pushbutton until
the following is displayed:
SETUP UNIT
stat comm SETUP
5. Press
ENTER
, then press the RIGHT
arrow pushbutton until the following is
displayed:
DATE & TIME
W
TIME error eth_ver diag
6. Press
ENTER
, the following will be
displayed:
DATE & TIME
08-Jan-2001 00:00:80
Summary of Contents for M-3425A
