Avery Dennison ALS 204, Service And Installation Manual

Page: 60 / 224

60
4.1 F
UNCTION MENU
4.1 F
UNCTION MENU
ALS
20X
256
Label 2 offset function:
– Only appears if LABEL SETUP > Multi label mode =
„x labels/start“.
– Defines the distance of the 2nd label and of all fol-
lowing labels, if x > 3 (see LABEL SETUP > Multi label
mode function). The distance is measured from the
front label edge of the preceding label.
– Setting range: [x…9999.9] mm; Default: x, with
x = LABEL SETUP > Label pitch .
Label 3 offset function:
– Only appears if LABEL SETUP > Multi label mode =
„3 labels/start“.
– Defines the distance of the 3rd label for the
LABEL SETUP > Multi label mode function (see above).
The distance is measured from the front label edge
of the preceding label.
– Setting range: [x…9999.9] mm; Default: x, with
x = LABEL SETUP > Label pitch .
Miss. label tol. function:
– Tolerance for missing labels
– Maximum permitted number of labels missing con-
secutively from the label ribbon
– Adjustment range: [0…10]; default: 1
Miss. label mode function:
– Determines the treatment of missing labels
– Settings: [
Compensate , Simulate]
Compensate: Quick feeding with slew speed (see
LABEL SETUP > Slew speed ) until the next label arrives
at the label sensor
Simulate: Missing labels are simulated. Feeding is
done in dispensing speed. Application example:
Operation of a printer, which is mounted to the
holding rods of the L-schape dispensing edge some
label length above the dispensing edge. In
„Compensate“ mode, one or more labels would
pass the printer unprinted.
With both settings, the machine switches into error
state, if the max. admissible number of missing
labels (
LABEL SETUP > Miss. label tol. ) is exceeded
(machine stops; error message; error signal active).
Stop count. mode function:
– Settings: [Enabled, Disabled ]
Enabled: The dispense counter counts down from
the value set in
LABEL SETUP > Label stop quan. When
the counter reaches 0, no further labels are
dispensed.
Disabled: The labeller counts up, i.e. each label
dispensed increases the counter reading.
Label stop quan. function:
– After this amount of dispensed labels, the dispenser
stops
– Function only appears, if
LABEL SETUP > Stop count.
mode
= „Enabled“
– Setting range: [0…99999]; default: 0
4.1.4
MACHINE SETUP menu
Dispenser type function:
– Sets the firmware to fit the machine type. The set-
ting must match the machine type!
– Settings: [„ALS 309 RH“, „ALS 309 LH“,
„ALS 306 RH“, „ALS 306 LH“, „ALS 256 RH“,
„ALS 256 LH“].
NOTICE! - By changing the machine type set-
ting all user defined factory settings are
deleted
(if MACHINE SETUP > Default values =
„User defined“).
Store prod.prof. function:
– Saves the current settings as a product profile
The extent of the stored functions is the same
as described in
MACHINE SETUP > Store
Parameters = „Without adj. par“ (file „setup.for“),
except for the following functions: MACHINE SET-
UP > Dispense counter and LABEL SETUP > Label stop quan. .
Del. prod.profil function:
– Deletes a product profile from the internal database
Dispense counter function:
– Enables dispense counter (displayed during label-
ling) to be adjusted by pressing the and
keys.
Disp. Cnt. Reset function:
– Settings: [ No , Yes]
Yes: Dispense counter is set to zero.
No: Dispense counter is not set to zero.
Turn-on mode function:
– Mode the machine is in after being switched on
– Settings: [
Online , Offline, Standalone]
Online: Labelling mode
Offline: mode for adjusting settings