manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual

The APRILIA RSV4 R Service Station Manual is an essential tool for motorcycle enthusiasts. This comprehensive manual provides users with detailed instructions on all aspects of servicing and maintaining their RSV4 R. Download this manual for free at manualshive.com and keep your bike running smoothly for years to come.

Share
Download
background image

continuity of the wiring is necessary for correct activation: no error indications are displayed in case of

lack of activation

DIAGNOSIS INSTRUMENT: ELECTRICAL ERRORS

fuel pump relay control P0230

•

shorted to positive / open circuit, shorted to negative.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 73 of the VEHICLE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 73 of the VEHICLE connector.

Troubleshooting

•

If shorted to positive: check whether the relay electrical specifications are correct by dis-

connecting it from the cable harness. If are not OK, replace the relay; if OK, restore the cable

harness (brown/black cable).

•

If the circuit is open, shorted to negative: check the relay electrical characteristics are correct

by disconnecting it from the cable harness; if it is not OK, replace the relay, if it is OK, check

relay connector, engine-vehicle cable harness connector and VEHICLE connector of the

Marelli control unit: if not OK, restore; if OK, check continuity of cable harness (brown/black

cable)

Coil

Function

Spark generation

Operation / operating principle

Inductive discharge system

Level in wiring diagram:

coils and injectors

Location:

•

on the vehicle: on the head covers.

•

connector: For each 3-ways black coil

connector. Coil 1 with short cable: on

the left on the filter box, rear side; coil

2 with long cable: on the left of the front

side of the filter box (connector with red

strap on engine cable harness), coil 3

with long cable: on the left on the rear

side of the filter box (connector with red

Electrical system

RSV4 R

ELE SYS - 184

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RSV4 R

Yamaha FJR1300AS Assembly Manual preview
FJR1300AS
Brand: Yamaha Pages: 94
Yamaha FJR1300(S) Supplementary Service Manual preview
FJR1300(S)
Brand: Yamaha Pages: 44
Honda CB110C3M Manual preview
CB110C3M
Brand: Honda Pages: 118
Qlink LG250 User Manual preview
LG250
Brand: Qlink Pages: 44
Happy Trails HTP1-12-7 Quick Start Manual preview
HTP1-12-7
Brand: Happy Trails Pages: 3
R&G BRG0004BK Fitting Instructions Manual preview
BRG0004BK
Brand: R&G Pages: 12
CYCLOPS KTM 1190 LED Light Bar Instructions preview
KTM 1190 LED Light Bar
Brand: CYCLOPS Pages: 4
yasuni TUB225 Assembly Instructions Manual preview
TUB225
Brand: yasuni Pages: 12
hepco & becker 661329 01 01 Quick Start Manual preview
661329 01 01
Brand: hepco & becker Pages: 4
KTM 690 Enduro R 2019 Owner'S Manual preview
690 Enduro R 2019
Brand: KTM Pages: 274
Zontes ZT310-X Service Manual preview
ZT310-X
Brand: Zontes Pages: 119
BOXER BM 100 Instruction Manual preview
BM 100
Brand: BOXER Pages: 11
Wolfman RTR4 Mounting Instructions preview
RTR4
Brand: Wolfman Pages: 3
CATU MO-185 Instruction Manual preview
MO-185
Brand: CATU Pages: 6
CATU MO-180-ARC4 Instruction Manual preview
MO-180-ARC4
Brand: CATU Pages: 8
Eastwood L6700 Instructions Manual preview
L6700
Brand: Eastwood Pages: 8
VESPA 125 Super Operation And Maintenance preview
125 Super
Brand: VESPA Pages: 46
Singing rock Kappa Instructions For Use preview
Kappa
Brand: Singing rock Pages: 2

Brands by name

Popular brands

Load more brands