manualshive.com logo in svg

APRILIA RSV4 R, Service Station Manual, Page: 294 / 475

Share
Download
APRILIA RSV4 R Service Station Manual Download Page 294

•

Remove the two crankshaft and cam-

shaft reference pins.

•

Turn the crankshaft until the gear

screw covered by the head when the

hole on the camshaft gear is aligned

with the hole on the U bolt, is visible.

•

Block crankshaft rotation using one of

the specific tools.

•

Unscrew and remove the camshaft

gear screw.

•

Remove the crankshaft locking tool.

Specific tooling

020850Y

 

Primary gear lock

020848Y

 

Flywheel retainer

Repeat the following operations:

•

move cylinder piston 1 (left rear piston)

to TDC;

•

turn the crankshaft by 450° (one com-

plete turn + 90°) in the direction of en-

gine rotation (direction of travel) to

align the hole on the intake camshaft

with the specific hole on the U bolt. This

ensures that all the rear cylinder bank

valve springs are decompressed.

•

Refit the camshaft timing setting pin in

the hole in the U bolt on the rear head,

and refit the crankshaft timing pin from

the clutch side, to check that the timing

setting was not altered while the en-

gine was turned with only one cam-

shaft drive gear fastener screw in

place.

•

Remove the camshaft timing pin.

•

Unscrew and remove the two U bolt

screws (1).

•

Remove the U bolt and the oil pipe.

Specific tooling

Engine

RSV4 R

ENG - 294

Summary of Contents for RSV4 R




























































































































































































































































































































































































































































































Reviews:

No comments